Thermador MEDS301WS Instruction manual - Page 34

Cleaning Your Oven

Page 34 highlights

Wi-Fi® Module FCC/IC Statements Model: COM2 FCC ID: 2AHES-COM2 IC: 21152-COM2 The Home Connect module is a communication device designed to provide communication between appliances and smart devices. This module is integrated at the factory, under direct control of BSH Home Appliances Corporation, and is not user servicable or upgradable. At least 77/8 inch (20 cm) separation distance should be maintained from device to user. FCC COMPLIANCE STATEMENT 9 CAUTION Changes or modifications not expressly approved could void your authority to use this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. INDUSTRY CANADA STATEMENT This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems. Cleaning Your Oven With good care and cleaning, your appliance will retain its appearance and remain fully functioning for a long time to come. We will explain here how you should correctly care for and clean your oven. Suitable Cleaning Agents To ensure that the different surfaces are not damaged by using the wrong cleaning agent, follow the information in the following table. Depending on the appliance model, not all of the areas listed may be on/in your appliance. NOTICE: Surface damage! Do not use any ▯ Harsh or abrasive cleaning agents ▯ Cleaning agents with a high alcohol content ▯ Hard scouring pads or abrasive cleaning sponges ▯ High-pressure cleaners or steam cleaners ▯ Special cleaners for cleaning the appliance while it is hot Wash new soft sponges and cloths thoroughly before use. Tip: Recommended cleaning and care products can be purchased through Customer Service. Observe the respective manufacturer's instructions. 9 WARNING RISK OF BURNS The appliance becomes very hot. Never touch the hot inside surfaces of the oven interior or heating elements. Always allow the appliance to cool down. Keep children away. Notes ▯ Slight differences in color on the front of the appliance are caused by the use of different materials, such as glass, plastic and metal. ▯ Shadows on the door panels, which look like streaks, are caused by reflections made by the interior lighting. ▯ Enamel is baked on at very high temperatures. This can cause some slight color variation. This is normal and does not affect operation. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

34
Wi-Fi
®
Module
FCC/IC Statements
Model: COM2
FCC ID: 2AHES-COM2
IC: 21152-COM2
The Home Connect module is a communication device
designed to provide communication between appliances
and smart devices.
This module is integrated at the factory, under direct
control of BSH Home Appliances Corporation, and is not
user servicable or upgradable. At least 7
7
/
8
inch (20 cm)
separation distance should be maintained from device to
user.
FCC COMPLIANCE STATEMENT
9
CAUTION
Changes or modifications not expressly approved
could void your authority to use this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received,
including interference that may cause undesired
operation.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-
exempt RSS standard(s).
Operation is subject to the following two conditions:
1.
This device may not cause interference, and
2.
This device must accept any interference, including
interference that may cause undesired operation of the
device.
Operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-
channel mobile satellite systems.
Cleaning Your Oven
With good care and cleaning, your appliance will retain
its appearance and remain fully functioning for a long
time to come. We will explain here how you should
correctly care for and clean your oven.
Suitable Cleaning Agents
To ensure that the different surfaces are not damaged by
using the wrong cleaning agent, follow the information in
the following table. Depending on the appliance model,
not all of the areas listed may be on/in your appliance.
NOTICE:
Surface damage!
Do not use any
Harsh or abrasive cleaning agents
Cleaning agents with a high alcohol content
Hard scouring pads or abrasive cleaning sponges
High-pressure cleaners or steam cleaners
Special cleaners for cleaning the appliance while it is
hot
Wash new soft sponges and cloths thoroughly before
use.
Tip:
Recommended cleaning and care products can be
purchased through Customer Service. Observe the
respective manufacturer's instructions.
9
WARNING
RISK OF BURNS
The appliance becomes very hot. Never touch the
hot inside surfaces of the oven interior or heating
elements. Always allow the appliance to cool down.
Keep children away.
Notes
Slight differences in color on the front of the appliance
are caused by the use of different materials, such as
glass, plastic and metal.
Shadows on the door panels, which look like streaks,
are caused by reflections made by the interior lighting.
Enamel is baked on at very high temperatures. This
can cause some slight color variation. This is normal
and does not affect operation.