Ricoh SP C352DN User Guide - Page 84

When the Data In Indicator Does Not Light Up or Flash, Driver Properties with Windows

Get Ricoh SP C352DN PDF manuals and user guides View all Ricoh SP C352DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

3. Troubleshooting Problem Printing does not start when using the extended wireless LAN in Ad-hoc Mode. Cause The correct Communication Mode is not set. If printing does not start, contact your service representative. Solution • Turn the main power switch off and then back on again. For details about how to turn on/off the main power switch, see page 23 "Turning On/Off the Power". • Change [Communication Mode] in [System Settings] to [802.11 Ad-hoc Mode], and then select [Off] for [Security Method]. For details about Communication Mode, see "Interface Settings", Operating Instructions. When the Data In Indicator Does Not Light Up or Flash When the Data In indicator does not light up or flash after a print job starts, data is not being sent to the printer. When the printer is connected to the computer using the interface cable Check that the print port setting is correct. When connecting the printer to the computer using a parallel interface, connect using LPT1 or LPT2. 1. Open the printer properties dialog box, and then click the [Ports] tab. For details about displaying the printer properties dialog box, see "Displaying the Printer Driver Properties with Windows", Operating Instructions. 2. In the [Print to the following port(s)] list, check that the correct port is selected. Network connection For details about the network connection, contact your administrator. 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Problem
Cause
Solution
Printing does not start when
using the extended wireless
LAN in Ad-hoc Mode.
The correct Communication
Mode is not set.
•
Turn the main power switch
off and then back on again.
For details about how to
turn on/off the main power
switch, see page 23
"Turning On/Off the
Power".
•
Change [Communication
Mode] in [System Settings]
to [802.11 Ad-hoc Mode],
and then select [Off] for
[Security Method]. For
details about
Communication Mode, see
"Interface Settings",
Operating Instructions.
If printing does not start, contact your service representative.
When the Data In Indicator Does Not Light Up or Flash
When the Data In indicator does not light up or flash after a print job starts, data is not being sent to the
printer.
When the printer is connected to the computer using the interface cable
Check that the print port setting is correct. When connecting the printer to the computer using a
parallel interface, connect using LPT1 or LPT2.
1.
Open the printer properties dialog box, and then click the [Ports] tab.
For details about displaying the printer properties dialog box, see "Displaying the Printer
Driver Properties with Windows", Operating Instructions.
2.
In the [Print to the following port(s)] list, check that the correct port is selected.
Network connection
For details about the network connection, contact your administrator.
3. Troubleshooting
82