Panasonic AJ-PX800G Basic Operating Instructions - Page 129
LOW 2CH MOV], [AVC-G6 2CH MOV], 256Kbps], [512Kbps], [1Mbps]
View all Panasonic AJ-PX800G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 129 highlights
[FILE SPLIT] [RECORDING SETTING] [PRE REC] [ONE CLIP REC] [SIMUL REC] [DUAL CODEC SETTING] Item [RECORDING HOLD] [ONE SHOT TIME] [INTERVAL TIME] [START DELAY] [CODEC USAGE] [PROXY REC MODE] [STREAMING MODE] [PROXY DISP] [QoS MAX RATE] [QoS MIN RATE] [STREAMING LATENCY] Chapter 6 Menu Operations - Menu list Description of settings Selects the split method of the recording file. [NORMAL]: Divides the file every 4 GB regardless of the recording format. [SHORT]: Divides the file every 128 seconds regardless of the recording format. ffFactory setting: [NORMAL] If the clip is recorded in one file, it cannot be copied to a P2 memory card or 32 GB microP2 memory card, or copied or exported to a storage. A clip will be divided to recording files of approximately 128 seconds when [SHORT] is selected, but they can be operated as a single clip when the thumbnails of clips are operated on the P2 device. A single continuous recording time is approximately 3.5 hours. [SHORT] is disabled in interval recording, one-shot recording, and loop recording modes. Selects whether to hold [RECORDING] settings. [ON]: Holds the settings. [OFF]: Does not hold the settings. It will always be [NORMAL] the next time when the power is turned on. ffFactory setting: [OFF] Sets the recording duration of one-shot recording. [1frm], [2frm], [4frm], [8frm], [16frm], [1s] ffFactory setting: [1frm] Sets the interval duration for interval recording. [2frm], [4frm], [8frm], [16frm], [1s], [2s], [5s], [10s], [30s], [1min], [5min], [10min] ffFactory setting: [2frm] Selects whether to delay the recording start time by approximately one second when performing interval recording or one-short recording. [ON], [OFF] ffFactory setting: [OFF] Selects whether to perform pre-recording. If [ON] is selected, pre-recording is performed for approximately three seconds in HD, and for approximately seven seconds in SD. [ON], [OFF] ffFactory setting: [OFF] Selects whether to perform one-clip recording. [ON], [OFF] ffFactory setting: [OFF] Selects whether to perform simultaneous recording. [ON], [OFF] ffFactory setting: [OFF] Selects media for recording proxy data. [PROXY REC(P2)]: Records proxy data to a P2 card. [PROXY REC(P2&SD)]: Records proxy data to both of a P2 card and SD memory card. [STREAMING]: Outputs video stream. [OFF]: Does not record proxy data or output streaming. ffFactory setting: [OFF] If [CODEC USAGE] cannot be changed, change the [PROXY REC MODE] or [STREAMING MODE] setting. Sets the recording mode of proxy data. [LOW 2CH MOV], [HQ 2CH MOV], [SHQ 2CH MOV], [AVC-G6 2CH MOV] ffFactory setting: [HQ 2CH MOV] Sets the transfer mode for streaming. [LOW], [HQ], [AVC‑G6], [SHQ (QoS)], [AVC-G (QoS)] ffFactory setting: [HQ] Selects whether to display proxy data recorded information or messages in the viewfinder. [ON]: Displays proxy recording information and SD memory card remaining capacity at the start of recording. Warning information is displayed at all times. [OFF]: Displays proxy and SD memory card warning information for only three seconds when warning occurs. ffFactory setting: [OFF] Sets the maximum bitrate for video data when the QoS is operating. This setting is used when the streaming distribution is started from the operation of the camera. This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING SETTING] → [START TRIGGER]. [256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps] ffFactory setting: [9Mbps] [9Mbps] cannot be selected when [STREAMING MODE] is set to [SHQ (QoS)]. Sets the minimum bitrate for video data when the QoS is operating. This setting is used when the streaming distribution is started from the operation of the camera. This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING SETTING] → [START TRIGGER]. [256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps] ffFactory setting: [256Kbps] Sets the delay mode during the streaming distribution. This setting is used when the streaming distribution is started from the operation of the camera. This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING SETTING] → [START TRIGGER]. [NORMAL]: Set this to prioritize the stability of streaming. [SHORT]: Set this to prioritize the reduction of streaming delay. ffFactory setting: [NORMAL] - 129 -