LiftMaster CAPXLV2 Installation Manual - English French Spanish - Page 20

OSDP Card Reader, Daisy-Chain, Connection

Get LiftMaster CAPXLV2 PDF manuals and user guides View all LiftMaster CAPXLV2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

INTRODUCTION ACCOUNT SETUP POWER NETWORK/MOUNTING ACCESS CONTROL OSDP Card Reader The CAPXLV2 is designed to connect a single or multiple OSDP readers. The OSDP reader should be installed by following the following steps: 1. Disconnect power from the CAPXLV2. 2. Prepare RS-485 cables before the connection by adding the matching resistors (100 ohms) to both ends of the cable. 3. Connect one end of the RS-485 cables and 12VDC power to the OSDP connector on the CAPXLV2 main board. 4. Turn on power of CAPXL2 and make sure it is in Admin mode. 5. Go to OSDP Tab in Admin Mode. 6. Toggle Enable Install New Reader. 7. Make sure the new OSDP reader has default address 0 by following the manufacturer's recommendation. If not, connect the OSDP reader to 12V power line and GND, using configuration card (5044-FEA-OSDP-018) to set to manufacture default and then disconnect 12V power line. 8. Connect the new OSDP reader to RS-485 cables. 9. The CAPXLV2 should discover the connected reader and create the reader in myQB. The reader should turn its LED to amber and beep three times. The OSDP reader is now installed. 10. To install more OSDP readers, follow steps 7 through 9 for each new OSDP reader. The uninstallation or deletion of the OSDP should follow the following steps: 1. Make sure the OSDP reader to be deleted is connected to RS485. Postal Lock DOC 2 DOC 1 USB 2 CAPXLV2 can only install one OSDP reader at a time. You must complete steps 7 through 9 for an OSDP reader before you connect another new OSDP reader to the RS-485 cables. GND D+ D12V +12VDC DD+ GND OSDP Never disconnect OSDP reader before uninstalling or deleting from Admin UI. 2. Go to Tab in Admin mode 3. Selected the OSDP reader to be deleted from the Connected Readers 4. Click Delete Button. 5. Click Delete in the confirmation pate 6. Check if the deleted reader is not displayed under Connected Readers. 7. Disconnect the deleted reader from RS485 cable and 12V power line. Add external resistor (100 Ohms) 100 Ohms SPKR 100 Ohms OSDP Daisy-Chain Connection 20 100 Ohms

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
20
INTRODUCTION
ACCOUNT SETUP
NETWORK/MOUNTING
POWER
ACCESS CONTROL
OSDP Card Reader
The CAPXLV2 is designed to connect a single or multiple OSDP
readers. The OSDP reader should be installed by following the
following steps:
1.
Disconnect power from the CAPXLV2.
2.
Prepare RS-485 cables before the connection by adding the
matching resistors (100 ohms) to both ends of the cable.
3.
Connect one end of the RS-485 cables and 12VDC power to
the OSDP connector on the CAPXLV2 main board.
4.
Turn on power of CAPXL2 and make sure it is in Admin mode.
5.
Go to OSDP Tab in Admin Mode.
6.
Toggle Enable Install New Reader.
7.
Make sure the new OSDP reader has default address 0
by following the manufacturer’s recommendation. If not,
connect the OSDP reader to 12V power line and GND,
using configuration card (5044-FEA-OSDP-018) to set to
manufacture default and then disconnect 12V power line.
8.
Connect the new OSDP reader to RS-485 cables.
9.
The CAPXLV2 should discover the connected reader and
create the reader in myQB. The reader should turn its LED
to amber and beep three times. The OSDP reader is now
installed.
10.
To install more OSDP readers, follow steps 7 through 9 for
each new OSDP reader.
The uninstallation or deletion of the OSDP should follow the
following steps:
1.
Make sure the OSDP reader to be deleted is connected to RS-
485.
2.
Go to Tab in Admin mode
3.
Selected the OSDP reader to be deleted from the Connected
Readers
4.
Click Delete Button.
5.
Click Delete in the confirmation pate
6.
Check if the deleted reader is not displayed under Connected
Readers.
7.
Disconnect the deleted reader from RS485 cable and 12V
power line.
CAPXLV2 can only install one OSDP reader at a time. You must
complete steps 7 through 9 for an OSDP reader before you
connect another new OSDP reader to the RS-485 cables.
OSDP
Daisy-Chain
Connection
Add external resistor
(100 Ohms)
USB 2
DOC 2
DOC 1
Postal
Lock
SPKR
OSDP
GND
D+
D-
12V
GND
D+
D-
+12VDC
100 Ohms
100 Ohms
100 Ohms
Never disconnect OSDP reader before uninstalling or deleting
from Admin UI.