LiftMaster CAPXLV Installation Manual - English French Spanish - Page 20

Door Access, Request To Exit, Supervised Door Status, Primary Relay, Auxiliary Relay, Wiegand, Door 1

Get LiftMaster CAPXLV PDF manuals and user guides View all LiftMaster CAPXLV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Door Access Disconnect power BEFORE making electrical connections. Below is an example of a wiring setup for door access. Door access can be wired to Door 1, 2, 3, or 4 on the Door Boards. WIEGAND KEYPAD READER NOTE: The length of the unshielded wires should be kept to a minimum to avoid electrical noise. OR NOTE: For KPR2000 keypad, wire the pink and black (ground) wires together. 12Vdc - red GROUND - black DATA 0 - green DATA 1 - white GREEN LED - orange RED LED - brown REQUEST TO EXIT PROXIMITY PUSH SENSOR BUTTON SUPERVISED (DOOR STATUS) DOOR SENSOR (SUPERVISED) OR DOOR SENSOR (NON-SUPERVISED) EOL (End of Line) Resistor (1k ohm) *PRIMARY RELAY DOOR STRIKE For AC Power: Install a Siemens S10K30MOV (Metal Oxide Varistor) (provided) or equivalent Power for Door Strike (Not Provided) Use 18-22 AWG COMMON + OR REQUEST TO EXIT GROUND SUPERVISED NORMALLY OPEN COMMON NORMALLY CLOSED NORMALLY OPEN COMMON - - NORMALLY OPEN For DC Power: Install a 1N4005 diode or equivalent OR MAGLOCK For AC Power: Install a Siemens S10K30MOV (Metal Oxide Varistor) (provided) or equivalent Use 18-22 AWG NORMALLY CLOSED For DC Power: Install a 1N4005 diode or equivalent COMMON + Power for Maglock (Not Provided) DO NOT use the power supply for the controller AUXILIARY RELAY Low Voltage Power Supply LIGHT NEUTRAL Isolation Relay LOAD LINE NOTE: DO NOT run high voltage power within OR the CAPXL enclosure. ALARM BYPASS COMMON NORMALLY OPEN 20 DOOR 1, 2, 3, or 4 * NOTE: MAGLOCK, door strike and ALARM BYPASS not evaluated by UL.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
20
+
–
+
–
PUSH
BUTTON
DOOR SENSOR
(SUPERVISED)
DOOR STRIKE
MAGLOCK
DOOR SENSOR
(NON-SUPERVISED)
OR
EOL (End of Line) Resistor
(1k ohm)
PROXIMITY
SENSOR
For DC Power:
Install a 1N4005
diode or equivalent
Use 18-22 AWG
Power for Maglock
(Not Provided)
DO NOT
use the power
supply for the controller
Use 18-22 AWG
For DC Power:
Install a 1N4005
diode or equivalent
Power for Door Strike
(Not Provided)
REQUEST TO EXIT
GROUND
SUPERVISED
NORMALLY OPEN
COMMON
NORMALLY CLOSED
NORMALLY OPEN
COMMON
NORMALLY OPEN
COMMON
NORMALLY CLOSED
COMMON
OR
OR
REQUEST TO EXIT
SUPERVISED (DOOR STATUS)
*PRIMARY RELAY
ALARM BYPASS
NORMALLY OPEN
COMMON
AUXILIARY RELAY
OR
NOTE:
The length of the unshielded
wires should be kept to a minimum to
avoid electrical noise.
RED LED - brown
GREEN LED - orange
DATA 1 - white
DATA 0 - green
GROUND - black
12Vdc - red
READER
OR
KEYPAD
WIEGAND
LIGHT
LOAD
LINE
NEUTRAL
NOTE:
DO NOT
run high voltage
power within
the CAPXL
enclosure.
Isolation
Relay
Low
Voltage
Power
Supply
NOTE:
For KPR2000
keypad, wire the pink and
black (ground) wires together.
For AC Power:
Install a Siemens S10K30MOV
(Metal Oxide Varistor) (provided)
or equivalent
For AC Power:
Install a Siemens
S10K30MOV
(Metal Oxide Varistor)
(provided) or equivalent
DOOR 1, 2, 3, or 4
* NOTE:
MAGLOCK, door strike
and ALARM BYPASS not
evaluated by UL.
Door Access
Disconnect power BEFORE making electrical connections.
Below is an example of a wiring setup for door access. Door access can be
wired to Door 1, 2, 3, or 4 on the Door Boards.
INTRODUCTION
PRE-INSTALL
NETWORK
INSTALL
ACCESS CONTROL