LiftMaster CAPXLV Installation Manual - English French Spanish - Page 16

Connect Power, Wire Specification, Maximum Run Distance

Get LiftMaster CAPXLV PDF manuals and user guides View all LiftMaster CAPXLV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL 5 Connect Power The outlet for the CAPXL / CAPXLV MUST be an external dedicated 120 Vac outlet. Refer to the table below for maximum wire run distances. This outlet should be wired back to its own 10 Amp minimum circuit breaker. WIRE SPECIFICATION 14 AWG 16 AWG 18 AWG MAXIMUM RUN DISTANCE Up to 300 feet (91.4 m) Up to 200 feet (60.9 m) Up to 100 feet (30.4 m) 1. Connect 14-18 AWG wire to the stripped secondary DC output wires on the power supply. Black is negative and red is positive. 2. Remove the PWR INPUT terminal block from the Power/Internet Board. 3. Connect the power supply wires to the PWR INPUT terminal block (red to +24V and black to GND). Reattach the terminal block to the Power/Internet Board. 4. Plug the power supply into a 120 Vac outlet after all connections have been made. NOTE: The green LED on the door board will blink and the green LED on the Power/Internet Board will light solid when powered up. The CAPXL / CAPXLV will display the LiftMaster logo while booting up. When boot up is complete, the user interface will appear. 5. Close the CAPXL / CAPXLV door. • DO NOT use ANY power supply other than those supplied with your CAPXL / CAPXLV. • DO NOT power electronic strikes and latches with the same power supply used to power the access control panel; doing so will cause DAMAGE to the CAPXL / CAPXLV. Use ONLY a UL listed burglar alarm or access control system to power electronic strikes and latches. • DO NOT connect the power supply to a switched outlet or otherwise controlled AC outlet. • DO NOT connect the power supply to the 120 Vac outlet until ALL wiring is completed. • Install the transient noise suppression device (MOV) supplied with the CAPXL / CAPXLV for AC powered devices and Diode for DC powered devices. ON POWER INPUT Power/Internet Board Dedicated 10 Amp Minimum Circuit NOTE: If the power supply is installed outdoors, the power supply must have its own approved NEMA 4 Rated weatherproof electrical enclosure. Use conduit from the power supply enclosure to the controller enclosure. Power Supply 16 120 Vac Dedicated Outlet

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
16
Connect Power
5
•
DO NOT use ANY power supply other
than those supplied with your CAPXL /
CAPXLV.
•
DO NOT power electronic strikes and
latches with the same power supply
used to power the access control panel;
doing so will cause DAMAGE to the
CAPXL / CAPXLV. Use ONLY a UL listed
burglar alarm or access control system
to power electronic strikes and latches.
•
DO NOT connect the power supply to a
switched outlet or otherwise controlled
AC outlet.
•
DO NOT connect the power supply to
the 120 Vac outlet until ALL wiring is
completed.
•
Install the transient noise suppression
device (MOV) supplied with the CAPXL /
CAPXLV for AC powered devices and
Diode for DC powered devices.
The outlet for the CAPXL / CAPXLV MUST be an external dedicated 120 Vac
outlet. Refer to the table below for maximum wire run distances. This outlet
should be wired back to its own 10 Amp minimum circuit breaker.
1.
Connect 14-18 AWG wire to the stripped secondary DC output wires on
the power supply. Black is negative and red is positive.
2.
Remove the PWR INPUT terminal block from the Power/Internet Board.
3.
Connect the power supply wires to the PWR INPUT terminal block (red
to +24V and black to GND). Reattach the terminal block to the
Power/Internet Board.
4.
Plug the power supply into a 120 Vac outlet after all connections have
been made.
NOTE:
The green LED on the door board will blink and the green
LED on the Power/Internet Board will light solid when powered up.
The CAPXL / CAPXLV will display the LiftMaster logo while booting
up. When boot up is complete, the user interface will appear.
5.
Close the CAPXL / CAPXLV door.
INTRODUCTION
PRE-INSTALL
NETWORK
INSTALL
ACCESS CONTROL
Dedicated 10 Amp Minimum Circuit
120 Vac
Dedicated Outlet
Power Supply
POWER INPUT
Power/Internet Board
NOTE: If the power supply is installed outdoors,
the power supply must have its own approved
NEMA 4 Rated weatherproof electrical enclosure.
Use conduit from the power supply enclosure to
the controller enclosure.
WIRE SPECIFICATION
MAXIMUM RUN DISTANCE
14 AWG
Up to 300 feet (91.4 m)
16 AWG
Up to 200 feet (60.9 m)
18 AWG
Up to 100 feet (30.4 m)