AEG AXP26U558HW User Manual - Page 13

Installation Instructions

Get AEG AXP26U558HW PDF manuals and user guides View all AEG AXP26U558HW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

5. INSTALLATION INSTRUCTIONS ENGLISH 13 5.1 Exhausting hot air In the Cool Mode the appliance must be placed close to a window or opening so that the warm exhaust air can be ducted outside. First position unit on a flat floor and make sure there's a minimum of 50cm clearance around the unit, and is within the vicinity of a single circuit outlet power source. 1. Extend either side of the hose (Fig. 1) and screw the hose to adaptor A (Fig. 2). 4. Affix the adaptor B into the window. (Fig. 5) ([WHQGWKHVLGHRIKRVH )LJ The hose can be extended from its original length of 38cm up to 150cm, but it is the best to keep the length to minimum required. Also make sure that the hose does not have any sharp bends or sags. (Fig. 6) Fig. 6 )LJ The adaptor A already be screwed to the hose for this unit. 2. Extend the other side of the hose and screw it to adaptor B (Fig. 3). )LJ 3. Install the adaptor A into the unit (Fig. 4).  6OLGHRQWR  /RFN Fig. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
13
ENGLISH
5.
INSTALLATION INSTRUCTIONS
5.1 Exhausting hot air
In the Cool Mode the appliance must be
placed close to a window or opening so
that the warm exhaust air can be ducted
outside. First position unit on a flat floor
and make sure there’s a minimum of
50cm clearance around the unit, and is
within the vicinity of a single circuit outlet
power source.
1.
Extend either side of the hose (Fig. 1)
and screw the hose to adaptor A (Fig. 2).
2.
Extend the other side of the hose and
screw it to adaptor B (Fig. 3).
The adaptor A already be screwed
to the hose for this unit.
4.
Affix the adaptor B into the window.
(Fig. 5)
3.
Install the adaptor A into the unit (Fig. 4).
Fig. 4
The hose can be extended from
its original length of 38cm up to
150cm, but it is the best to keep
the length to minimum required.
Also make sure that the hose
does not have any sharp bends
or sags. (Fig. 6)
Fig. 6