2010 Yamaha Motorsports Phazer R-TX Owners Manual - Page 59

2010 Yamaha Motorsports Phazer R-TX Manual

Get 2010 Yamaha Motorsports Phazer R-TX PDF manuals and user guides View all 2010 Yamaha Motorsports Phazer R-TX manuals

Page 59 highlights

Periodic maintenance and adjustment 1. Spark plug gap 2. Spark plug reach 1. Rubber cap 5. Before installing any spark plug, measure the electrode gap with a wire thickness gauge and adjust to specification. Spark plug gap: 0.6-0.7 mm (0.024-0.028 in) When installing the spark plug, always clean the gasket surface. Wipe off any grime from the threads and tighten the spark plug to the specified torque. Spark plug tightening torque: 12.5 Nm (1.25 m·kgf, 9 ft·lbf) ECS00382 Insert a Phillips screwdriver into the hole, and then turn the idle adjusting screw in or out to adjust the engine idling speed. 1. Idle adjusting screw NOTICE Make sure that the spark plug caps are securely installed. Otherwise the spark plug caps could be damaged due to engine vibration. ESU11812 Standard engine idling speed: 1700-1900 r/min 6. Install the rubber cap. ESU11840 Adjusting the engine idling speed 1. 2. 3. 4. Place the snowmobile on a level surface and apply the parking brake. Start the engine and warm it up. Select the engine speed meter mode. (See page 11 for details.) Remove the rubber cap. Adjusting the throttle cable free play (PZ50RT / PZ50GT / PZ50MT) 1. 2. Loosen the locknut. Turn the adjusting bolt in or out until the proper throttle cable free play is achieved. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance and adjustment
53
Before installing any spark plug, measure the
electrode gap with a wire thickness gauge
and adjust to specification.
When installing the spark plug, always clean
the gasket surface. Wipe off any grime from
the threads and tighten the spark plug to the
specified torque.
NOTICE
ECS00382
Make sure that the spark plug caps are se-
curely installed. Otherwise the spark plug
caps could be damaged due to engine vi-
bration.
ESU11812
Adjusting the engine idling
speed
1.
Place the snowmobile on a level surface
and apply the parking brake.
2.
Start the engine and warm it up.
3.
Select the engine speed meter mode.
(See page 11 for details.)
4.
Remove the rubber cap.
5.
Insert a Phillips screwdriver into the hole,
and then turn the idle adjusting screw in
or out to adjust the engine idling speed.
6.
Install the rubber cap.
ESU11840
Adjusting the throttle cable free
play (PZ50RT / PZ50GT /
PZ50MT)
1.
Loosen the locknut.
2.
Turn the adjusting bolt in or out until the
proper
throttle
cable
free
play
is
achieved.
1.
Spark plug gap
2.
Spark plug reach
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Spark plug tightening torque:
12.5 Nm (1.25 m·kgf, 9 ft·lbf)
1.
Rubber cap
1.
Idle adjusting screw
Standard engine idling speed:
1700–1900 r/min