2010 Yamaha Motorsports Phazer R-TX Owners Manual - Page 37

2010 Yamaha Motorsports Phazer R-TX Manual

Page 37 highlights

Control functions rection (b) more than 12 click(s). Even if the adjusting knob is continually turned after 12 click(s), there will be no change in the damping force. Be sure to stop the adjusting knob at a position where there is a click. [ECS00910] (b) 1 (a) 1. Compression damping force adjusting knob Compression damping force setting: Minimum (soft): 12 click(s) in direction (b)* Standard: 6 click(s) in direction (b)* Maximum (hard): 1 click(s) in direction (b)* * With the adjusting knob fully turned in direction (a) ESU11033 1. Locknut 2. Control rod adjusting nut 2. Adjusting the control rods (PZ50VT) EWS00770 WARNING The left and right adjusting nuts must be set to the same position. Uneven settings can cause poor handling and loss of stability. The weight transfer can be adjusted by turning the adjusting nuts on the control rods. 1. Loosen the locknut while holding the adjusting nut. To increase weight transfer, turn the adjusting nut in direction (a), and to decrease weight transfer, turn it in direction (b). WARNING! Never adjust the control rods beyond the maximum setting, indicated by red paint; otherwise, they could be damaged, which could lead to an accident or injury. [EWS00173] 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98

Control functions
31
rection (b) more than 12 click(s). Even if
the adjusting knob is continually turned
after 12 click(s), there will be no change in
the damping force. Be sure to stop the ad-
justing knob at a position where there is a
click.
[ECS00910]
ESU11033
Adjusting the control rods (PZ50VT)
WARNING
EWS00770
The left and right adjusting nuts must be
set to the same position. Uneven settings
can cause poor handling and loss of sta-
bility.
The weight transfer can be adjusted by turn-
ing the adjusting nuts on the control rods.
1.
Loosen the locknut while holding the ad-
justing nut.
2.
To increase weight transfer, turn the ad-
justing nut in direction (a), and to de-
crease weight transfer, turn it in direction
(b).
WARNING! Never adjust the con-
trol rods beyond the maximum set-
ting, indicated by red paint; otherwise,
they could be damaged, which could
lead to an accident or injury.
[EWS00173]
1.
Compression damping force adjusting knob
Compression damping force setting:
Minimum (soft):
12 click(s) in direction (b)*
Standard:
6 click(s) in direction (b)*
Maximum (hard):
1 click(s) in direction (b)*
* With the adjusting knob fully turned in
direction (a)
(b)
(a)
1
1. Locknut
2.
Control rod adjusting nut