2010 Yamaha Motorsports Apex LTX GT Owners Manual - Page 54

2010 Yamaha Motorsports Apex LTX GT Manual

Get 2010 Yamaha Motorsports Apex LTX GT PDF manuals and user guides View all 2010 Yamaha Motorsports Apex LTX GT manuals

Page 54 highlights

Periodic maintenance and adjustment 9. Install the headlight unit bolts, and then tighten them to the specified torque. Headlight unit bolt tightening torque: 3 Nm (0.3 m·kgf, 2.2 ft·lbf) Check the T.O.R.S. for proper operation. 1. Start the engine. TIP Refer to the "Starting the engine" section on page 31. 2. Hold the pivot point of the throttle lever away from the throttle switch by putting your thumb (above) and forefinger (below) between the throttle lever pivot and the engine stop switch housing. While holding the pivot point as described above, squeeze the throttle lever gradually. 10. Tighten the quick fastener screws on the top cover. 11. Install the shroud. ESU11863 Checking the throttle override system (T.O.R.S.) EWS00352 WARNING When checking the T.O.R.S., take precautions to avoid snowmobile movement which could cause an accident: G Make sure that the throttle lever moves smoothly with the engine off before checking the T.O.R.S. G Make sure that the parking brake is applied. G Do not rev the engine to the point that the clutch engages. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance and adjustment
48
9.
Install the headlight unit bolts, and then
tighten them to the specified torque.
10.
Tighten the quick fastener screws on the
top cover.
11.
Install the shroud.
ESU11863
Checking the throttle override
system (T.O.R.S.)
WARNING
EWS00352
When checking the T.O.R.S., take precau-
tions to avoid snowmobile movement
which could cause an accident:
●
Make sure that the throttle lever moves
smoothly with the engine off before
checking the T.O.R.S.
●
Make sure that the parking brake is ap-
plied.
●
Do not rev the engine to the point that
the clutch engages.
Check the T.O.R.S. for proper operation.
1.
Start the engine.
TIP
Refer to the “Starting the engine” section on
page 31.
2.
Hold the pivot point of the throttle lever
away from the throttle switch by putting
your thumb (above) and forefinger (be-
low) between the throttle lever pivot and
the engine stop switch housing.
While holding the pivot point as described
above, squeeze the throttle lever gradu-
ally.
Headlight unit bolt tightening torque:
3 Nm (0.3 m·kgf, 2.2 ft·lbf)