2008 Yamaha Motorsports Phazer GT Owners Manual - Page 63

2008 Yamaha Motorsports Phazer GT Manual

Get 2008 Yamaha Motorsports Phazer GT PDF manuals and user guides View all 2008 Yamaha Motorsports Phazer GT manuals

Page 63 highlights

Periodic maintenance 2. Remove the coolant reservoir cap, add the recommended coolant until it reaches the "COLD LEVEL" mark, and then install the cap. NOTE: If you find any leaks, consult a Yamaha dealer. 5. Install the right upper cover, and then install the top cover (PZ50RT / PZ50GT / PZ50MT) or close the shroud (PZ50VT). ESU12080 V-belt EWS00400 WARNING G 1. "COLD LEVEL" mark 2. Coolant reservoir cap G Make sure that the drive guard is tightened securely before operating the snowmobile. Never run the engine with the V-belt or drive guard removed. Recommended antifreeze: High-quality ethylene glycol antifreeze containing corrosion inhibitors Antifreeze and water mixing ratio: 3:2 Total amount: PZ50GT 3.60 L (3.81 US qt) (3.17 Imp.qt) PZ50MT 3.60 L (3.81 US qt) (3.17 Imp.qt) PZ50RT 3.60 L (3.81 US qt) (3.17 Imp.qt) PZ50VT 3.70 L (3.91 US qt) (3.26 Imp.qt) 3. 4. Start the engine, allow it to idle for several minutes, and then turn it off. Check for any coolant leakage. The V-belt should be checked before each ride. To check the V-belt 1. Remove the left side cover (PZ50RT / PZ50GT / PZ50MT), or open the shroud and remove the left upper cover and the left side cover (PZ50VT). (See page 45 for removal procedure.) 2. Remove the drive guard. 3. Check the V-belt for wear and damage. Replace if necessary. 1. V-belt wear limit New V-belt width: 34.1 mm (1.34 in) V-belt wear limit width: 32.5 mm (1.28 in) 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Periodic maintenance
57
2.
Remove the coolant reservoir cap, add
the recommended coolant until it reaches
the “COLD LEVEL” mark, and then install
the cap.
3.
Start the engine, allow it to idle for several
minutes, and then turn it off.
4.
Check for any coolant leakage.
NOTE:
If you find any leaks, consult a Yamaha deal-
er.
5.
Install the right upper cover, and then in-
stall the top cover (PZ50RT / PZ50GT /
PZ50MT) or close the shroud (PZ50VT).
ESU12080
V-belt
WARNING
EWS00400
●
Make sure that the drive guard is tight-
ened securely before operating the
snowmobile.
●
Never run the engine with the V-belt or
drive guard removed.
The V-belt should be checked before each
ride.
To check the V-belt
1.
Remove the left side cover (PZ50RT /
PZ50GT / PZ50MT), or open the shroud
and remove the left upper cover and the
left side cover (PZ50VT). (See page 45
for removal procedure.)
2.
Remove the drive guard.
3.
Check the V-belt for wear and damage.
Replace if necessary.
1.
“COLD LEVEL” mark
2.
Coolant reservoir cap
Recommended antifreeze:
High-quality ethylene glycol antifreeze
containing corrosion inhibitors
Antifreeze and water mixing ratio:
3:2
Total amount:
PZ50GT 3.60 L (3.81 US qt) (3.17
Imp.qt)
PZ50MT 3.60 L (3.81 US qt) (3.17
Imp.qt)
PZ50RT 3.60 L (3.81 US qt) (3.17
Imp.qt)
PZ50VT 3.70 L (3.91 US qt) (3.26
Imp.qt)
1.
V-belt wear limit
New V-belt width:
34.1 mm (1.34 in)
V-belt wear limit width:
32.5 mm (1.28 in)