2008 Yamaha Motorsports Phazer GT Owners Manual - Page 60

2008 Yamaha Motorsports Phazer GT Manual

Get 2008 Yamaha Motorsports Phazer GT PDF manuals and user guides View all 2008 Yamaha Motorsports Phazer GT manuals

Page 60 highlights

Periodic maintenance G G Use only 4-stroke engine oil. Make sure that no foreign material enters the engine oil tank. 7. Insert the dipstick into the oil filler hole, and then tighten the oil filler cap. 8. Connect the oil level gauge coupler. 9. Install the right side cover (PZ50RT / PZ50GT / PZ50MT), or install the right side cover and the right upper cover, and then close the shroud (PZ50VT). To change the engine oil (without oil filter cartridge replacement) 1. Place the snowmobile on a level surface, and apply the parking brake. 2. Start the engine, warm it up for several minutes, and then turn it off. 3. Remove the right side cover (PZ50RT / PZ50GT / PZ50MT), or open the shroud and remove the right upper cover and the right side cover (PZ50VT). (See page 45 for removal procedure.) 4. Remove the bottom panel and the right lower cover. 1. Right lower cover 5. 6. Place an oil pan under the oil tank to collect the used oil. Disconnect the oil level gauge coupler. 1. Oil level gauge coupler 2. Oil filler cap 7. Remove the oil filler cap and drain bolt to drain the oil from the oil tank. 1. Bottom panel 1. Engine oil drain bolt (oil tank) 8. Place an oil pan under the engine to collect the used oil. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Periodic maintenance
54
●
Use only 4-stroke engine oil.
●
Make sure that no foreign material en-
ters the engine oil tank.
7.
Insert the dipstick into the oil filler hole,
and then tighten the oil filler cap.
8.
Connect the oil level gauge coupler.
9.
Install the right side cover (PZ50RT /
PZ50GT / PZ50MT), or install the right
side cover and the right upper cover, and
then close the shroud (PZ50VT).
To change the engine oil (without oil filter car-
tridge replacement)
1.
Place the snowmobile on a level surface,
and apply the parking brake.
2.
Start the engine, warm it up for several
minutes, and then turn it off.
3.
Remove the right side cover (PZ50RT /
PZ50GT / PZ50MT), or open the shroud
and remove the right upper cover and the
right side cover (PZ50VT). (See page 45
for removal procedure.)
4.
Remove the bottom panel and the right
lower cover.
5.
Place an oil pan under the oil tank to col-
lect the used oil.
6.
Disconnect the oil level gauge coupler.
7.
Remove the oil filler cap and drain bolt to
drain the oil from the oil tank.
8.
Place an oil pan under the engine to col-
lect the used oil.
1.
Bottom panel
1.
Right lower cover
1.
Oil level gauge coupler
2.
Oil filler cap
1.
Engine oil drain bolt (oil tank)