2008 Yamaha Motorsports Phazer GT Owners Manual - Page 18

2008 Yamaha Motorsports Phazer GT Manual

Get 2008 Yamaha Motorsports Phazer GT PDF manuals and user guides View all 2008 Yamaha Motorsports Phazer GT manuals

Page 18 highlights

Control functions ESU10471 Low coolant temperature indicator light " " The low coolant temperature indicator light comes on when the coolant temperature is low and informs the rider that the snowmobile should be warmed up. After the engine is started, warm it up until the indicator light goes off. 1. "SELECT" button 2. "RESET" button NOTE: G G To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode "ODO", and then push the "SELECT" button for at least 10 seconds while the snowmobile is stopped. Use the engine speed meter only when checking the snowmobile and performing basic maintenance. The engine speed meter should not be used while riding the snowmobile since the reading will vary from the actual engine speed. 1. Low coolant temperature indicator light " " The snowmobile can be operated normally after the indicator light goes off. NOTE: Operate the snowmobile at low speeds when the low coolant temperature indicator light is on. If the engine speed is too high, maximum engine speed is reduced to protect the engine. ESU10500 ESU10410 High beam indicator light " " The high beam indicator light comes on when the high beams of the headlights are switched on. (See page 17 for headlight beam switch operation.) Knock control system "KCS" indicator light This snowmobile is equipped with a system which detects engine knocking in order to protect the engine from damage. The knock control system "KCS" indicator light comes on if knocking is detected, then flashes if the knocking increases. 1. High beam indicator light " " 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Control functions
12
NOTE:
●
To switch the speedometer, odometer, and
tripmeter displays between kilometers and
miles, select the odometer mode “ODO”,
and then push the “SELECT” button for at
least 10 seconds while the snowmobile is
stopped.
●
Use the engine speed meter only when
checking the snowmobile and performing
basic maintenance. The engine speed
meter should not be used while riding the
snowmobile since the reading will vary from
the actual engine speed.
ESU10410
High beam indicator light “
”
The high beam indicator light comes on when
the high beams of the headlights are switched
on. (See page 17 for headlight beam switch
operation.)
ESU10471
Low coolant temperature indi-
cator light “
”
The low coolant temperature indicator light
comes on when the coolant temperature is
low and informs the rider that the snowmobile
should be warmed up. After the engine is
started, warm it up until the indicator light
goes off.
The snowmobile can be operated normally af-
ter the indicator light goes off.
NOTE:
Operate the snowmobile at low speeds when
the low coolant temperature indicator light is
on. If the engine speed is too high, maximum
engine speed is reduced to protect the en-
gine.
ESU10500
Knock control system “KCS”
indicator light
This snowmobile is equipped with a system
which detects engine knocking in order to pro-
tect the engine from damage.
The knock control system “KCS” indicator
light comes on if knocking is detected, then
flashes if the knocking increases.
1.
“SELECT” button
2.
“RESET” button
1.
High beam indicator light “
”
1.
Low coolant temperature indicator light
“
”