BenQ W1110 User Manual - Page 24

Selecting an input source

Get BenQ W1110 PDF manuals and user guides View all BenQ W1110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Selecting an input source The projector can be connected to multiple equipment at the same time. However, it only displays one full screen at a time. When starting up, the projector automatically searches for the available signals. If you want the projector to always automatically search for the signals: • Under the Advanced OSD menu, go to the System Setup : Basic menu, and enable Auto Source. (see "Auto Source" on page 41) • Under the Basic OSD menu, if there's no signal connected to the projector, go to Auto Source and enable it; if there are signals connected, go to the Settings menu, and then enable Auto Source. (see "Auto Source" on page 30 and 32) To select the video source: 1. Press SOURCE on the projector or remote control to display the source selection bar. Source HDMI1 HDMI2 PC Video Component 2. Press / until your desired signal is selected and press OK. Once detected, the selected source information displays on the screen for seconds. If there are multiple pieces of equipment connected to the projector, repeat steps 1-2 to search for another signal. The native display resolution of this projector is in a 16:9 aspect ratio. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the Aspect Ratio setting, which may cause some image distortion or loss of picture clarity. See "Aspect Ratio" for details. Renaming an input source You may rename the current input source on the source selection bar. To do this, first and foremost, you have to access the Advanced OSD menu (see page 28 for details). 1. Press MENU and then use / to go to System Setup : Basic. 2. Press to select Source Rename and press OK to display the Source Rename window. 3. Press / / / until your desired character is selected. 4. When done, press BACK to save your changes and exit. 24 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
24
Operation
Selecting an input source
The projector can be connected to multiple equipment at the same time. However, it only displays one
full screen at a time. When starting up, the projector automatically searches for the available signals.
If you want the projector to always automatically search for the signals:
•
Under the
Advanced
OSD menu, go to the
System Setup : Basic
menu, and enable
Auto
Source
. (see
"Auto Source" on page 41
)
•
Under the
Basic
OSD menu, if there’s no signal connected to the projector, go to
Auto Source
and
enable it; if there are signals connected, go to the
Settings
menu, and then enable
Auto Source.
(see
"Auto Source" on page 30
and
32
)
To select the video source:
1.
Press
SOURCE
on the projector or remote control to display the source selection bar.
2.
Press
/
until your desired signal is selected and press
OK
.
Once detected, the selected source information displays on the screen for seconds. If there are
multiple pieces of equipment connected to the projector, repeat steps 1-2 to search for another
signal.
The native display resolution of this projector is in a 16:9 aspect ratio. For best display picture results, you
should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by
the projector depending upon the Aspect Ratio setting, which may cause some image distortion or loss of
picture clarity. See "
Aspect Ratio
" for details.
Renaming an input source
You may rename the current input source on the source selection bar.
To do this, first and foremost, you have to access the
Advanced
OSD menu (see page
28
for details).
1.
Press
MENU
and then use
/
to go to
System Setup : Basic
.
2.
Press
to select
Source Rename
and press
OK
to display the
Source Rename
window.
3.
Press
/
/
/
until your desired character is selected.
4.
When done, press
BACK
to save your changes and exit.
HDMI1
HDMI2
Video
Component
PC
Source