2012 Yamaha Motorsports Phazer R-TX Owners Manual - Page 78

2012 Yamaha Motorsports Phazer R-TX Manual

Get 2012 Yamaha Motorsports Phazer R-TX PDF manuals and user guides View all 2012 Yamaha Motorsports Phazer R-TX manuals

Page 78 highlights

Periodic maintenance and adjustment Shifted to left 1. 2. 3. 4. 5. Forward Gap Slide runner Drive track Slide metal 1. Slide runner 2. Wear limit height Slide runner wear limit height: 10.5 mm (0.41 in) ECS00350 5. Adjust the drive track deflection to specification. NOTICE: The right and left adjusting nuts should be turned an equal amount. [ECS00592] Drive track deflection More than specified Turn in Turn in Less than specified Turn out Turn out NOTICE Ride on fresh snow frequently. Operating on ice or hard-packed snow will rapidly wear the slide runners. ESU12181 Left adjusting nut Right adjusting nut High-profile pattern drive track (PZ50MT) This snowmobile is originally equipped with a 51 mm (2.0 in) high-profile pattern drive track specifically for use in deep snow riding conditions. Therefore, avoid prolonged operation on hard surfaces such as ice, hard-packed snow, dirt, etc., to extend the life of the track and slide runners. 6. 7. 8. Recheck alignment and deflection. If necessary, repeat steps 3 to 5 until the proper adjustment is achieved. Lower the snowmobile to the ground. Tighten the rear axle nut. Rear axle nut tightening torque: 75 Nm (7.5 m·kgf, 54 ft·lbf) Slide runners Check the slide runners for wear and damage. If the slide runners reach the wear limit, they should be replaced. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Periodic maintenance and adjustment
72
Shifted to left
5.
Adjust the drive track deflection to speci-
fication.
NOTICE:
The right and left ad-
justing nuts should be turned an equal
amount.
[ECS00592]
6.
Recheck alignment and deflection. If nec-
essary, repeat steps 3 to 5 until the prop-
er adjustment is achieved.
7.
Lower the snowmobile to the ground.
8.
Tighten the rear axle nut.
Slide runners
Check the slide runners for wear and dam-
age.
If the slide runners reach the wear limit, they
should be replaced.
NOTICE
ECS00350
Ride on fresh snow frequently. Operating
on ice or hard-packed snow will rapidly
wear the slide runners.
ESU12181
High-profile pattern drive track
(PZ50MT)
This snowmobile is originally equipped with a
51 mm (2.0 in) high-profile pattern drive track
specifically for use in deep snow riding condi-
tions.
Therefore, avoid prolonged operation on hard
surfaces such as ice, hard-packed snow, dirt,
etc., to extend the life of the track and slide
runners.
1. Forward
2. Gap
3.
Slide runner
4.
Drive track
5.
Slide metal
Drive track
deflection
More than
specified
Less than
specified
Left adjusting
nut
Turn in
Turn out
Right adjust-
ing nut
Turn in
Turn out
Rear axle nut tightening torque:
75 Nm (7.5 m·kgf, 54 ft·lbf)
1.
Slide runner
2.
Wear limit height
Slide runner wear limit height:
10.5 mm (0.41 in)