2013 Polaris Ness Signature Series Cross Country Tour Owners Manual - Page 86

2013 Polaris Ness Signature Series Cross Country Tour Manual

Get 2013 Polaris Ness Signature Series Cross Country Tour PDF manuals and user guides View all 2013 Polaris Ness Signature Series Cross Country Tour manuals

Page 86 highlights

Maintenance Side Covers Remove the left side cover to access the electronic control module, diagnostic connector and chassis-to-engine harness connector. Remove the right side cover to access the fuses, rear suspension air fitting, clutch cable adjuster, purge valve and flasher unit. Remove both side covers to access the seat screws. 1. Pull outward at each corner of the side cover to disengage the three darts. 2. Remove the side cover from the motorcycle. 3. To reinstall the side cover, make sure each rubber grommet is properly positioned. Align each dart with the appropriate grommet and press inward firmly to secure each dart. Grommets Trunk Removal (CROSS COUNTRY TOUR) 1. Open both saddlebag covers. Remove the left saddlebag and side cover. Place them in a safe location to prevent damage to the Latch painted surfaces. Release 2. Disconnect the trunk wire harness. 3. Pull the two trunk latch levers fully upward to release the latches. 4. From the rear of the motorcycle, grasp the trunk firmly with both hands. Pull the trunk assembly rearward to disengage the trunk support legs from the saddlebag support bracket bushings. 5. Place the trunk assembly in a safe location to prevent damage. 6. Reinstall the side cover and left saddlebag. 7. Reverse this procedure to reinstall the trunk assembly. Make sure the trunk support legs are firmly anchored onto the saddelbag support bracket bushings. Push both trunk latch levers fully downward to engage the latches. When properly latched, theft prevention bolts prevent latches from rotating and releasing. WARNING! An insecurely latched trunk assembly can cause loss of control resulting in serious injury or death. Always make sure trunk latches are secure before operating the motorcycle. 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
84
Maintenance
Side Covers
Remove the left side cover to access the elec-
tronic control module, diagnostic connector and
chassis-to-engine harness connector.
Remove the right side cover to access the fuses,
rear suspension air fitting, clutch cable adjuster,
purge valve and flasher unit.
Remove both side covers to access the seat
screws.
1.
Pull outward at each corner of the side cover
to disengage the three darts.
2.
Remove the side cover from the motorcycle.
3.
To reinstall the side cover, make sure each
rubber grommet is properly positioned. Align
each dart with the appropriate grommet and
press inward firmly to secure each dart.
Trunk Removal (CROSS COUNTRY TOUR)
1.
Open both saddlebag covers. Remove the
left saddlebag and side cover. Place them in
a safe location to prevent damage to the
painted surfaces.
2.
Disconnect the trunk wire harness.
3.
Pull the two trunk latch levers fully upward
to release the latches.
4.
From the rear of the motorcycle, grasp the
trunk firmly with both hands. Pull the trunk
assembly rearward to disengage the trunk
support legs from the saddlebag support
bracket bushings.
5.
Place the trunk assembly in a safe location to prevent damage.
6.
Reinstall the side cover and left saddlebag.
7.
Reverse this procedure to reinstall the trunk assembly. Make sure the trunk support legs
are firmly anchored onto the saddelbag support bracket bushings. Push both trunk latch
levers fully downward to engage the latches. When properly latched, theft prevention
bolts prevent latches from rotating and releasing.
WARNING!
An insecurely latched trunk assembly can cause loss of control resulting in serious injury
or death. Always make sure trunk latches are secure before operating the motorcycle.
Grommets
Latch
Release