2013 Polaris Ness Signature Series Cross Country Tour Owners Manual - Page 38

2013 Polaris Ness Signature Series Cross Country Tour Manual

Get 2013 Polaris Ness Signature Series Cross Country Tour PDF manuals and user guides View all 2013 Polaris Ness Signature Series Cross Country Tour manuals

Page 38 highlights

Instruments, Features and Controls Fairing Vents and Deflectors (CROSS COUNTRY TOUR) An air vent and a deflector are located in each lower fairing. Use the vent handles to open and close the vents. Do not force a vent to open beyond the vent pivot stop. Move a deflector inward or outward to adjust air flow. WARNING! Failure to inspect deflector clearance after removing and reinstalling a fairing could result in steering interference, which could result in serious injury or death. After removing and reinstalling a fairing, always check for adequate steering clearance by moving the handlebars fully to the left and fully to the right, first with the deflectors open and again with the deflectors closed. Make any adjustments necessary to ensure steering clearance. Passenger Floorboard Supports (CROSS COUNTRY TOUR) The passenger floorboard height and angle can be adjusted. To adjust the angle, loosen both attachment screws. Rotate the floorboard to the desired position using the indicator mark on the rear-facing support as a guide, then tighten the screws. Torque: 18 ft-lbs (24.4 Nm) To adjust the height, remove both attachment screws. Move the floorboard assembly to the next hole position, then reinstall the fasteners, adjust the angle and tighten the fasteners to the recommended torque. Attachment Screws 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
36
Instruments, Features and Controls
Fairing Vents and Deflectors (CROSS COUNTRY TOUR)
An air vent and a deflector are located in each lower fairing. Use the vent handles to open
and close the vents. Do not force a vent to open beyond the vent pivot stop. Move a deflector
inward or outward to adjust air flow.
WARNING!
Failure to inspect deflector clearance after removing and reinstalling a fairing could result
in steering interference, which could result in serious injury or death.
After removing and reinstalling a fairing, always check for adequate steering clearance by
moving the handlebars fully to the left and fully to the right, first with the deflectors open
and again with the deflectors closed. Make any adjustments necessary to ensure steering
clearance.
Passenger Floorboard Supports (CROSS COUNTRY TOUR)
The passenger floorboard height and angle can be
adjusted. To adjust the angle, loosen both attachment
screws. Rotate the floorboard to the desired position using
the indicator mark on the rear-facing support as a guide,
then tighten the screws.
Torque:
18 ft-lbs (24.4 Nm)
To adjust the height, remove both attachment screws.
Move the floorboard assembly to the next hole position,
then reinstall the fasteners, adjust the angle and tighten the
fasteners to the recommended torque.
Attachment
Screws