Smeg DOU330X1 Instruction Manual - Page 28

Setting the Self-Clean Mode

Get Smeg DOU330X1 PDF manuals and user guides View all Smeg DOU330X1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Use & Care Manual ENGLISH Setting the Self-Clean Mode To Set the Self-Clean Mode 1. Touch [UPPER/LOWER] key to select the cavity to be cleaned, if the oven is a double. 2. Rotate both knobs into the clean position. 3. CLEAN & TIME appear. 4. The clean time is displayed automatically, its standard value is 3 hours. 5. At the end of the programmed cleaning time, the oven will automatically turn off. 6. To stop the cleaning mode at any moment, move one of the two knobs from the cleaning position. Do not attempt to open the door while the door is locked. The "AUTO LOCK" writings will flash until the motor stops. When they are displayed, the door cannot be opened. Check that the door has been locked and will not open before starting the Self-Clean mode. If door does not lock, rotate the cooking mode knob into the OFF position and do not start self-clean; phone for service. If the door is in the open position when this mode is selected, the "AUTO LOCK" writings will flash until the door is closed. The latch doesn't move. To Change the Cleaning Time 1. To change the setting from 3 hours, select either 2 hours for light soil or 4 hours for heavy soil immediately before starting. 2. To change the hours, touch the [TIME] key. 3. The hours will flash. 4. Use [INC] or [DEC] keys to change the value. 5. To change the minutes, touch the [TIME] key again. 6. The minutes will flash. 7. Use [INC] or [DEC] keys to change the value. Hold the key to change by 10 minutes steps. 8. Touch [TIME] or wait a few seconds to confirm the new value. To Delay the Start of Cleaning 1. Follow steps 1 through 7 above. 2. Touch the [TIME] key and verify that "STOP TIME" appears on the display. The hours will begin flashing. 3. Use [INC] or [DEC] keys to change the stop time value. 4. To change the minutes, touch the [TIME] key, the minutes will flash. 5. Use [INC] or [DEC] keys to change the value. Hold the key to change by 10 minutes steps. 6. Touch [TIME] or wait a few seconds to confirm the new value. 7. The latch starts moving to lock the oven door, the display shows "DELAY". 8. When the delay time expires, self-cleaning will start. 9. At the end of the programmed cleaning time, the oven will automatically turn off. 10. "End" will appear on the temperature display, "CLEAN" on the mode display and "TIME" on the clock display will start flashing until the [TIME] key is touched or the knob is moved to the OFF position. In order to check the cleaning or the stop time during a delayed clean, simply touch the [TIME] key until "TIME" or "STOP TIME" writings are displayed. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
Use & Care Manual
ENGLISH
28
Setting the Self-Clean Mode
To Set the Self-Clean Mode
1. Touch [UPPER/LOWER] key to select the
cavity to be cleaned, if the oven is a double.
2.
Rotate both knobs into the clean position.
3.
CLEAN & TIME appear.
4.
The clean time is displayed automatically, its
standard value is 3 hours.
5.
At the end of the programmed cleaning time,
the oven will automatically turn off.
6. To stop the cleaning mode at any moment,
move one of the two knobs from the cleaning
position.
Do not attempt to open the door while the door is
locked. The “AUTO LOCK” writings will flash until the
motor stops. When they are displayed, the door
cannot be opened. Check that the door has been
locked and will not open before starting the Self-Clean
mode.
If door does not lock, rotate the cooking mode knob
into the OFF position and do not start self-clean;
phone for service.
If the door is in the open position when this mode is
selected, the “AUTO LOCK” writings will flash until the
door is closed. The latch doesn’t move.
To Change the Cleaning Time
1. To change the setting from 3 hours, select
either 2 hours for light soil or 4 hours for
heavy soil immediately before starting.
2.
To change the hours, touch the [TIME] key.
3.
The hours will flash.
4.
Use [INC] or [DEC] keys to change the value.
5. To change the minutes, touch the [TIME] key
again.
6.
The minutes will flash.
7.
Use [INC] or [DEC] keys to change the value.
Hold the key to change by 10 minutes steps.
8.
Touch [TIME] or wait a few seconds to confirm
the new value.
To Delay the Start of Cleaning
1.
Follow steps 1 through 7 above.
2. Touch the [TIME] key and verify that
“STOP
TIME”
appears on the display. The hours will
begin flashing.
3. Use [INC] or [DEC] keys to change the stop
time value.
4.
To change the minutes, touch the [TIME] key,
the minutes will flash.
5.
Use [INC] or [DEC] keys to change the value.
Hold the key to change by 10 minutes steps.
6.
Touch [TIME] or wait a few seconds to confirm
the new value.
7.
The latch starts moving to lock the oven door,
the display shows
“DELAY”
.
8.
When the delay time expires, self-cleaning will
start.
9. At the end of the programmed cleaning time,
the oven will automatically turn off.
10.
“End”
will appear on the temperature display,
“CLEAN”
on the mode display and
“TIME”
on
the clock display will start flashing until the
[TIME] key is touched or the knob is moved to
the OFF position.
In order to check the cleaning or the stop time during a
delayed clean, simply touch the [TIME] key until “TIME”
or “STOP TIME” writings are displayed.