Ricoh MP 3555 User Guide - Page 235

When Other Messages Appear, PDF encryption level: 128Bit AES

Page 235 highlights

When Other Messages Appear When Other Messages Appear Message Cause Solution "Firmware update will start. Press [OK]. It will start automatically after 30 seconds have elapsed." Automatic firmware update is enabled and it is the time for an automatic update. • If you want to start the firmware update, press [OK], or configure the setting so that the automatic firmware update starts automatically in 30 seconds. • If you do not want to start the firmware update, press [Cancel] before 30 seconds elapse. • Do not turn off the power switch during the firmware update. "Cannot connect with the wireless card. Turn the main power switch off, then check the card." (A "wireless LAN board" is referred to as a "wireless card".) • The wireless LAN board was not inserted when the machine was turned on. • The wireless LAN board was pulled out after the machine was turned on. The settings are not updated although the unit is detected. Turn off the power, and then check the wireless LAN board is inserted correctly. After this, turn on the power again. If the message appears again, contact your service representative. "Failed to read the PDF file." There is a possibility that the PDF version is not supported by the browser's PDF viewer or an unsupported encryption level is specified. With this machine's browser PDF files other than those whose versions and encryption levels are specified below cannot be viewed. • PDF version: 1.3-1.7 • PDF encryption level: 128Bit AES or 256Bit AES "Clean the scanning glass. (Located next to the exposure glass.)" The scanning glass or guide plate of the ADF is dirty. Clean the scanning glass or guide plate. See "Maintaining Your Machine", Maintenance and Specifications. "Following output tray is full. The output tray is full. Remove paper." Remove paper from the output tray to resume printing. Press [Continue] on the display panel to resume printing. 233

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256

When Other Messages Appear
Message
Cause
Solution
"Firmware update will start.
Press [OK]. It will start
automatically after 30
seconds have elapsed."
Automatic firmware update
is enabled and it is the time
for an automatic update.
If you want to start the firmware
update, press [OK], or configure
the setting so that the automatic
firmware update starts
automatically in 30 seconds.
If you do not want to start the
firmware update, press [Cancel]
before 30 seconds elapse.
Do not turn off the power switch
during the firmware update.
"Cannot connect with the
wireless card. Turn the main
power switch off, then check
the card."
(A "wireless LAN board" is
referred to as a "wireless
card".)
The wireless LAN
board was not inserted
when the machine was
turned on.
The wireless LAN
board was pulled out
after the machine was
turned on.
The settings are not updated
although the unit is detected.
Turn off the power, and then check the
wireless LAN board is inserted
correctly. After this, turn on the power
again. If the message appears again,
contact your service representative.
"Failed to read the PDF file."
There is a possibility that the
PDF version is not supported
by the browser's PDF viewer
or an unsupported
encryption level is specified.
With this machine's browser PDF files
other than those whose versions and
encryption levels are specified below
cannot be viewed.
PDF version: 1.3-1.7
PDF encryption level: 128Bit AES
or 256Bit AES
"Clean the scanning glass.
(Located next to the
exposure glass.)"
The scanning glass or guide
plate of the ADF is dirty.
Clean the scanning glass or guide
plate. See "Maintaining Your
Machine", Maintenance and
Specifications.
"Following output tray is full.
Remove paper."
The output tray is full.
Remove paper from the output tray to
resume printing. Press [Continue] on
the display panel to resume printing.
When Other Messages Appear
233