Rane HAL1x Installation Guide - Page 79

Working with DHCP, Static IP Addresses, and Routers, HAL SYSTEM INSTALL GUIDE

Get Rane HAL1x PDF manuals and user guides View all Rane HAL1x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

HAL SYSTEM INSTALL GUIDE WARNING! If your network requires that the HAL use one or more static IP addresses, you should configure these addresses prior to connecting the HAL to your network. To do so, install and start the Halogen software, connect your computer directly to the device, and then open the device and configure its IP address(es). For details, see "Working with DHCP, Static IP Addresses, and Routers" below. 3. Using the IEC power cord provided with the product, connect the HAL to a power outlet or power strip. The Power LED located on both the front and rear panels of the HAL lights up. 4. Verify that the Ethernet connection is working properly. l When plugged into any working Ethernet port, the Ethernet Link LED (located on both the front and rear panels) lights up. l If there is activity on the network (in other words, network packets are being transmitted), the Ethernet LAN LED (on the rear panel) flashes. l The Ethernet Comm LED (on the front panel) flashes if the HAL hardware is communicating with at least one PC that is running RaneLink II. The LED is solid when Halogen is connected to the HAL. 5. If the shielded CAT 5e cabling for the RADs and DRs has already been installed and terminated, connect the cables to the appropriate RAD and DR ports on the rear panel of the HAL (and EXP devices, if applicable). Working with DHCP, Static IP Addresses, and Routers Does your installation require the use of DHCP and/or static IP addresses? Do you need to set up DNS and a Gateway so that your HAL can synchronize its internal clock with an NTP Server? Never fear, it's as simple as can be. But there are a few things you need to know as well as a few issues that could arise: l To configure a static IP or enable DHCP on a HAL, you should first connect directly to the HAL via its link-local address. In other words, it is best to configure these addresses prior to connecting the HAL to your network. To do so, install the Halogen software (see "Installing and Starting the Halogen Software" on page 89), connect your computer directly to the HAL device (see "Task 2: Configuring HAL" on the facing page), start Halogen, connect to the HAL from within Halogen, and then open the HAL properties (by clicking the HAL device properties icon in its title bar in the Halogen Hardware Workspace-see the Halogen Help System for details), and then configure its IP addresses (and/or enable DHCP). Once the system is installed at the site, you (and all subsequent users) may need to type in a static IP address to search for, and connect to the HAL, so write this IP address somewhere! l On a local network, Halogen always uses the link-local IP (169.254.x.y) to connect to HAL. Behind a router, Halogen uses one of HAL's static IPs or a DHCP-assigned IP-provided the user knows it and types it into the Search field in the Connect to Device dialog box. Because link-local connectivity is automatic, the user should never need to search for a HAL by its link-local IP address. NOTE: If your HAL is located on the WAN side of a router and Halogen is unable to find the HAL, check with your IT department to find out if the router has NAT (Network Address Translation) enabled. If not, enable it and try again. l Although Halogen does not prevent you from adding a static IP that conflicts with a static IP on another machine on the network, it does prevent the addition of a duplicate IP on the same HAL. l TIP: To change a static IP address to another value, you must first delete the existing IP address and 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
WARNING
!
If your network requires that the HAL use one or more static IP addresses, you should
configure these addresses prior to connecting the HAL to your network. To do so, install and start
the Halogen software, connect your computer directly to the device, and then open the device and
configure its IP address(es). For details, see "Working with DHCP, Static IP Addresses, and Routers"
below.
3.
Using the IEC power cord provided with the product, connect the HAL to a power outlet or power strip.
The Power LED located on both the front and rear panels of the HAL lights up.
4.
Verify that the Ethernet connection is working properly.
l
When plugged into any working Ethernet port, the Ethernet Link LED (located on both the front
and rear panels) lights up.
l
If there is activity on the network (in other words, network packets are being transmitted), the Eth-
ernet LAN LED (on the rear panel) flashes.
l
The Ethernet Comm LED (on the front panel) flashes if the HAL hardware is communicating with
at least one PC that is running RaneLink II. The LED is solid when Halogen is connected to the
HAL.
5.
If the shielded CAT 5e cabling for the RADs and DRs has already been installed and terminated, connect
the cables to the appropriate RAD and DR ports on the rear panel of the HAL (and EXP devices, if appli-
cable).
Working with DHCP, Static IP Addresses, and Routers
Does your installation require the use of DHCP and/or static IP addresses? Do you need to set up DNS and a Gate-
way so that your HAL can synchronize its internal clock with an NTP Server? Never fear, it's as simple as can be.
But there are a few things you need to know as well as a few issues that could arise:
l
To configure a static IP or enable DHCP on a HAL, you should first connect directly to the HAL via its
link-local address. In other words, it is best to configure these addresses prior to connecting the HAL to
your network. To do so, install the Halogen software (see "Installing and Starting the Halogen Software" on
page 89), connect your computer directly to the HAL device (see "Task 2: Configuring HAL" on the facing
page), start Halogen, connect to the HAL from within Halogen, and then open the HAL properties (by click-
ing the HAL device properties icon in its title bar in the Halogen Hardware Workspace—see the Halogen
Help System for details), and then configure its IP addresses (and/or enable DHCP). Once the system is
installed at the site, you (and all subsequent users) may need to type in a static IP address to search for, and
connect to the HAL, so
write this IP address somewhere!
l
On a local network, Halogen always uses the link-local IP (169.254.x.y) to connect to HAL. Behind a
router, Halogen uses one of HAL’s static IPs or a DHCP-assigned IP—provided the user knows it and types
it into the Search field in the
Connect to Device
dialog box. Because link-local connectivity is automatic,
the user should never need to search for a HAL by its link-local IP address.
NOTE
:
If your HAL is located on the WAN side of a router and Halogen is unable to find the HAL,
check with your IT department to find out if the router has NAT (Network Address Translation) ena-
bled. If not, enable it and try again.
l
Although Halogen does not prevent you from adding a static IP that conflicts with a static IP on another
machine on the network, it does prevent the addition of a duplicate IP on the same HAL.
l
TIP
:
To change a static IP address to another value, you must first delete the existing IP address and
HAL SYSTEM INSTALL GUIDE
73