Rane HAL1x Installation Guide - Page 103

Device, Behavior when placed in Locate Mode, The Power, Comm, Audio Tx

Get Rane HAL1x PDF manuals and user guides View all Rane HAL1x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

CHAPTER 4: Introduction to the Halogen Software Device Type Behavior when placed in Locate Mode HAL The Locate LED on the front and rear panels of the corresponding device flashes green. The Power, Comm, Audio Tx, and Audio Rx LEDs on the corresponding RAD flash green. RAD NOTE: The bottom four status LEDs flash green to indicate Locate mode and flash red to indicate a model Mismatch. To aid those that may have difficulty distinguishing the two colors, the rate at which these LEDs flash is also different for each mode. The rate for indicating a model mismatch (flashing red) is twice as fast as the rate used to indicate locate mode (flashing green). DR1 DR2 A flashing capital L within a circle appears on the corresponding device's LCD screen and the DR3 backlight flashes. PAGER1 DR4 The Locate LED on the front and rear panels of the corresponding DR4 flashes green. DR5 The Power and Comm LEDs on the front of the corresponding DR5 flash green. EXP The Locate LED on the front and rear panels of the corresponding EXP flashes green. NOTE: The Locate indicator in the software and on the device hardware continues flashing until you cancel the request in the software, interrupt the connection between the computer and HAL, disconnect the device, or power cycle the HAL. 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Device
Type
Behavior when placed in Locate Mode
HAL
The Locate LED on the front and rear panels of the corresponding device flashes green.
RAD
The Power, Comm, Audio Tx, and Audio Rx LEDs on the corresponding RAD flash green.
NOTE
:
The bottom four status LEDs flash green to indicate Locate mode and flash red to
indicate a model Mismatch. To aid those that may have difficulty distinguishing the two
colors, the rate at which these LEDs flash is also different for each mode. The rate for indi-
cating a model mismatch (flashing red) is twice as fast as the rate used to indicate locate
mode (flashing green).
DR1
DR2
DR3
PAGER1
A flashing capital L within a circle appears on the corresponding device's LCD screen and the
backlight flashes.
DR4
The Locate LED on the front and rear panels of the corresponding DR4 flashes green.
DR5
The Power and Comm LEDs on the front of the corresponding DR5 flash green.
EXP
The Locate LED on the front and rear panels of the corresponding EXP flashes green.
NOTE
:
The Locate indicator in the software and on the device hardware continues flashing until you cancel
the request in the software, interrupt the connection between the computer and HAL, disconnect the device,
or power cycle the HAL.
CHAPTER 4: Introduction to the Halogen Software
97