Epson TM-T88IV TM-T88IV Technical Reference Guide - Page 38

For Parallel/LAN/Wireless LAN Interface, DIP switch bank 1

Get Epson TM-T88IV PDF manuals and user guides View all Epson TM-T88IV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

For Parallel/LAN/Wireless LAN Interface DIP switch bank 1 SW Function 1-1 Auto line feed 1-2 Receive buffer capacity Selects paper sensors to 1-3 o u t p u t p a p e r- e n d s i g n a l s (default value of a command) 1-4 1-5 ∼ 1-8 Error signal output Undefined ON Always enabled 45 bytes Disabled Disabled - OFF Always disabled 4 KB Roll paper end sensor enabled, roll paper near-end sensor enabled Enabled Factory setting OFF OFF OFF OFF - OFF DIP switch bank 2 SW 2-1 2-2 2-3 ∼ 2-4 2-5 2-6 ∼ 2-7 2-8 Function ON OFF Handshaking (BUSY condition) Receive buffer full • Offline • Receive buffer full Reserved (Do not change setting) Fixed to OFF S e l e c t s p r i n t d e n s i t y / L ow See "Selecting the Print Density (DIP Switch power consumption mode 2-3/2-4)" on page 41. Setting the release condition of the receive buffer BUSY state (This function is effective when DIP switch 1-2 is set to off.) Releases the BUSY state when the remaining capacity of the receive buffer reaches 138 bytes. Releases the BUSY state when the remaining capacity of the receive buffer reaches 256 bytes. Reserved (Do not change settings) Fixed to OFF IF pin 31 reset signal (Do not change settings) Fixed to ON Factory setting OFF OFF OFF OFF OFF ON 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
38
For Parallel/LAN/Wireless LAN Interface
DIP switch bank 1
DIP switch bank 2
SW
Function
ON
OFF
Factory
setting
1-1
Auto line feed
Always enabled
Always disabled
OFF
1-2
Receive buffer capacity
45 bytes
4 KB
OFF
1-3
Selects paper sensors to
output paper-end signals
(default value of a command)
Disabled
Roll paper end
sensor enabled, roll
paper near-end
sensor enabled
OFF
1-4
Error signal output
Disabled
Enabled
OFF
1-5
∼
1-8
Undefined
—
—
OFF
SW
Function
ON
OFF
Factory
setting
2-1
Handshaking (BUSY condition)
Receive buffer full
•
Offline
•
Receive buffer full
OFF
2-2
Reserved (Do not change
setting)
Fixed to OFF
OFF
2-3
∼
2-4
Selects print density/Low
power consumption mode
See
"Selecting the Print Density (DIP Switch
2-3/2-4)" on page 41
.
OFF
2-5
Setting the release condition
of the receive buffer BUSY
state (This function is effective
when DIP switch 1-2 is set to
off.)
Releases the BUSY
state when the
remaining capacity
of
the
receive
buffer reaches 138
bytes.
Releases the BUSY
state when the
remaining capacity
of
the
receive
buffer reaches 256
bytes.
OFF
2-6
∼
2-7
Reserved (Do not change
settings)
Fixed to OFF
OFF
2-8
IF pin 31 reset signal (Do not
change settings)
Fixed to ON
ON