2012 Yamaha Motorsports RS Vector Owners Manual - Page 104

2012 Yamaha Motorsports RS Vector Manual

Page 104 highlights

Periodic maintenance and adjustment ESU13702 Drive track and slide runners Drive track EWS00481 WARNING A broken track, track fittings or debris thrown by the drive track could be dangerous to an operator or bystanders. Observe the following precautions: G Do not allow anyone to stand behind the snowmobile when the engine is running. G When the rear of the snowmobile is raised to allow the drive track to spin, a suitable stand must be used to support the rear of the snowmobile. Never allow anyone to hold the rear of the snowmobile off the ground to allow the drive track to spin. Never allow anyone near a rotating drive track. G Inspect the drive track condition frequently. Replace any damaged slide metal. Replace the drive track if it is damaged to the depth where fabric reinforcement material is visible or support rods are broken. Otherwise, track damage or failure could result in loss of braking ability and snowmobile control, which could cause an accident. 1. Area where projection cannot be installed 4. Tighten the front handlebar bolts to the specified torque, and then tighten the rear handlebar bolts to the specified torque. NOTICE: Make sure each handlebar holder is installed so that the smaller gap is facing forward. [ECS00582] Checking the drive track EWS00490 WARNING Do not operate the snowmobile if you find damage to the drive track, or if it has been maladjusted. Drive track damage or failure could result in loss of braking ability and snowmobile control, which could cause an accident. Check the drive track alignment and deflection, and check the track for wear and damage. 1. Forward 2. Small gap Handlebar bolt tightening torque: 23 Nm (2.3 m·kgf, 17 ft·lbf) 5. Install the handlebar cover. 98

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142

Periodic maintenance and adjustment
98
4.
Tighten the front handlebar bolts to the
specified torque, and then tighten the
rear handlebar bolts to the specified
torque.
NOTICE:
Make sure each han-
dlebar holder is installed so that the
smaller gap is facing forward.
[ECS00582]
5.
Install the handlebar cover.
ESU13702
Drive track and slide runners
Drive track
WARNING
EWS00481
A broken track, track fittings or debris
thrown by the drive track could be danger-
ous to an operator or bystanders. Observe
the following precautions:
Do not allow anyone to stand behind the
snowmobile when the engine is running.
When the rear of the snowmobile is
raised to allow the drive track to spin, a
suitable stand must be used to support
the rear of the snowmobile. Never allow
anyone to hold the rear of the snowmo-
bile off the ground to allow the drive
track to spin. Never allow anyone near a
rotating drive track.
Inspect the drive track condition fre-
quently. Replace any damaged slide
metal. Replace the drive track if it is
damaged to the depth where fabric rein-
forcement material is visible or support
rods are broken. Otherwise, track dam-
age or failure could result in loss of
braking ability and snowmobile control,
which could cause an accident.
Checking the drive track
WARNING
EWS00490
Do not operate the snowmobile if you find
damage to the drive track, or if it has been
maladjusted. Drive track damage or failure
could result in loss of braking ability and
snowmobile control, which could cause
an accident.
Check the drive track alignment and deflec-
tion, and check the track for wear and dam-
age.
1.
Area where projection cannot be installed
1. Forward
2.
Small gap
Handlebar bolt tightening torque:
23 Nm (2.3 m·kgf, 17 ft·lbf)