2009 Yamaha Motorsports Apex LTX GT Owners Manual - Page 62

2009 Yamaha Motorsports Apex LTX GT Manual

Get 2009 Yamaha Motorsports Apex LTX GT PDF manuals and user guides View all 2009 Yamaha Motorsports Apex LTX GT manuals

Page 62 highlights

Periodic maintenance and adjustment 9. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 1. Secondary sliding sheave 2. Secondary fixed sheave 10. Install the V-belt between the secondary sliding and fixed sheaves. 1. V-belt position adjusting bolt 2. Spacer V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer 1. V-belt Not necessary (It is correct.) 11. Install the drive guard, and then install the left side cover and the shroud. ESU12103 Add spacer Drive chain housing To check the drive chain housing oil level 1. Place the snowmobile on a level surface and apply the parking brake. 2. Remove the shroud and the right side cover. (See page 41 for removal procedures.) 3. Remove the dipstick, wipe it off with a clean rag, and then insert it back into the filler hole. 7. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) 8. Install the V-belt over the primary sheave assembly. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Periodic maintenance and adjustment
56
7.
Tighten the V-belt position adjusting
bolts.
8.
Install the V-belt over the primary sheave
assembly.
9.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
10.
Install the V-belt between the secondary
sliding and fixed sheaves.
11.
Install the drive guard, and then install the
left side cover and the shroud.
ESU12103
Drive chain housing
To check the drive chain housing oil level
1.
Place the snowmobile on a level surface
and apply the parking brake.
2.
Remove the shroud and the right side
cover. (See page 41 for removal proce-
dures.)
3.
Remove the dipstick, wipe it off with a
clean rag, and then insert it back into the
filler hole.
1.
V-belt position adjusting bolt
2. Spacer
V-belt position
Adjustment
More than 1.5 mm
(0.06 in) above the
edge
Remove spacer
From 1.5 mm (0.06 in)
above the edge to 0.5
mm (0.02 in) below
the edge
Not necessary (It is
correct.)
More than 0.5 mm
(0.02 in) below the
edge
Add spacer
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt