2009 Yamaha Motorsports Apex LTX GT Owners Manual - Page 61

2009 Yamaha Motorsports Apex LTX GT Manual

Get 2009 Yamaha Motorsports Apex LTX GT PDF manuals and user guides View all 2009 Yamaha Motorsports Apex LTX GT manuals

Page 61 highlights

Periodic maintenance and adjustment 2. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 1. Secondary sliding sheave 2. Secondary fixed sheave 3. Pull the V-belt up over the secondary fixed sheave. 1. Edge of the secondary sheave assembly 2. V-belt position Standard V-belt position: From 1.5 mm (0.06 in) above the edge of the secondary sheave assembly to 0.5 mm (0.02 in) below the edge 1. V-belt 6. 4. 5. Remove the V-belt from the secondary sheave assembly and primary sheave assembly. Temporarily install the new V-belt on the secondary sheave assembly only, and then measure the V-belt position. Do not force the V-belt between the sheaves; the secondary sliding and fixed sheaves must touch each other. If the V-belt position is incorrect, adjust it by removing or adding a spacer on each V-belt position adjusting bolt. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Periodic maintenance and adjustment
55
2.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
3.
Pull the V-belt up over the secondary
fixed sheave.
4.
Remove the V-belt from the secondary
sheave assembly and primary sheave
assembly.
5.
Temporarily install the new V-belt on the
secondary sheave assembly only, and
then measure the V-belt position. Do not
force the V-belt between the sheaves; the
secondary sliding and fixed sheaves
must touch each other.
6.
If the V-belt position is incorrect, adjust it
by removing or adding a spacer on each
V-belt position adjusting bolt.
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt
1.
Edge of the secondary sheave assembly
2.
V-belt position
Standard V-belt position:
From 1.5 mm (0.06 in) above the edge
of the secondary sheave assembly to
0.5 mm (0.02 in) below the edge