2011 Polaris Cross Country Owners Manual - Page 82

2011 Polaris Cross Country Manual

Get 2011 Polaris Cross Country PDF manuals and user guides View all 2011 Polaris Cross Country manuals

Page 82 highlights

Maintenance Seat Removal / Installation 1. Remove the side covers. See page 77. 2. Remove the two seat screws. Tool: 6 mm Allen wrench Seat Screws 10 ft-lbs (13.5 Nm) 3. Lift the front of the seat upward and pull forward to disengage the tab at the rear of the seat. 4. To install, reverse the above process, being sure to engage the tab at the back of the seat. 5. Tighten the seat screws. Torque: 10 ft-lbs (13.5 Nm) Headlight Aim Inspection The top edge of the high beam must be 3 inches (7.6 cm) below the widest part of the headlight and centered straight ahead at 25 feet (7.6 m). CROSS ROADS (High Beam) 25 ft. (7.6 m) 3 in. (7.6 cm) CROSS COUNTRY (High Beam) 25 ft. (7.6 m) 3 in. (7.6 cm) Height of widest part of headlight Height of widest part of headlight 1. 2. 3. 4. Verify that tire pressure is at specification. See page 74. Verify that rear suspension ride height (preload) is at specification. See page 64. Position the motorcycle on a level surface with the headlight 25 feet (7.6 m) from a wall. With the operator and passenger (if applicable) on board, bring the motorcycle to the fully upright position. 5. Move the ignition switch to the ON position and switch the headlamp to high beam. Observe the headlight aim on the wall. 6. Make any necessary adjustments to headlight aim. See page 79. 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
78
Maintenance
Seat Removal / Installation
1.
Remove the side covers. See page 77.
2.
Remove the two seat screws.
Tool:
6 mm Allen wrench
3.
Lift the front of the seat upward and pull
forward to disengage the tab at the rear of
the seat.
4.
To install, reverse the above process, being
sure to engage the tab at the back of the
seat.
5.
Tighten the seat screws.
Torque:
10 ft-lbs (13.5 Nm)
Headlight Aim Inspection
The top edge of the high beam must be 3 inches (7.6 cm) below the widest part of the head-
light and centered straight ahead at 25 feet (7.6 m).
1.
Verify that tire pressure is at specification. See page 74.
2.
Verify that rear suspension ride height (preload) is at specification. See page 64.
3.
Position the motorcycle on a level surface with the headlight 25 feet (7.6 m) from a wall.
4.
With the operator and passenger (if applicable) on board, bring the motorcycle to the
fully upright position.
5.
Move the ignition switch to the ON position and switch the headlamp to high beam.
Observe the headlight aim on the wall.
6.
Make any necessary adjustments to headlight aim. See page 79.
Seat Screws
10 ft-lbs (13.5 Nm)
25 ft. (7.6 m)
3 in. (7.6 cm)
Height of widest part
of headlight
CROSS ROADS (High Beam)
25 ft. (7.6 m)
CROSS COUNTRY (High Beam)
Height of widest part
of headlight
3 in. (7.6 cm)