2011 Polaris Cross Country Owners Manual - Page 38

2011 Polaris Cross Country Manual

Get 2011 Polaris Cross Country PDF manuals and user guides View all 2011 Polaris Cross Country manuals

Page 38 highlights

Instruments, Features and Controls Pedal Adjustment The brake pedal and gear shift pedal controls can be adjusted to a front, rear or center position. The center position is the factory setting. 1. Remove the screw from the footwell support. Tool: 6 mm Allen wrench 2. Slide the control forward or rearward in its track until the threaded hole of the control aligns with the desired hole in the footrest support. 3. Reinstall the screw. Torque: 96 in-lbs (11 Nm) 4. After adjusting the shift pedal, always readjust the shift linkage rod. Loosen both jam nuts on the linkage and turn the shaft until the footpeg is about 90 mm from the floorboard (or to desired height). Tighten both jam nuts. Torque: 96 in-lbs (11 Nm) Center Adjustment Position Sidestand The sidestand is located on the left side of the motorcycle. WARNING! An improperly retracted sidestand could contact the ground and cause a loss of control resulting in serious injury or death. Always retract the sidestand fully before operating the motorcycle. To park the motorcycle, swing the end of the sidestand downward and away from the motorcycle until it is fully extended. Lean the motorcycle to the left until the sidestand firmly supports the motorcycle. To retract the sidestand, straddle the motorcycle and bring it to the fully upright position. Swing the end of the sidestand upward and toward the motorcycle until it is fully retracted. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
34
Instruments, Features and Controls
Pedal Adjustment
The brake pedal and gear shift pedal controls can be
adjusted to a front, rear or center position. The center
position is the factory setting.
1.
Remove the screw from the footwell support.
Tool:
6 mm Allen wrench
2.
Slide the control forward or rearward in its track
until the threaded hole of the control aligns with
the desired hole in the footrest support.
3.
Reinstall the screw.
Torque:
96 in-lbs (11 Nm)
4.
After adjusting the shift pedal, always readjust the
shift linkage rod. Loosen both jam nuts on the
linkage and turn the shaft until the footpeg is about
90 mm from the floorboard (or to desired height).
Tighten both jam nuts.
Torque:
96 in-lbs (11 Nm)
Sidestand
The sidestand is located on the left side of the motorcycle.
WARNING!
An improperly retracted sidestand could contact the
ground and cause a loss of control resulting in serious injury or
death. Always retract the sidestand fully before operating the
motorcycle.
To park the motorcycle, swing the end of the sidestand down-
ward and away from the motorcycle until it is fully extended.
Lean the motorcycle to the left until the sidestand firmly sup-
ports the motorcycle.
To retract the sidestand, straddle the motorcycle and bring it
to the fully upright position. Swing the end of the sidestand
upward and toward the motorcycle until it is fully retracted.
Center Adjustment
Position