2007 Polaris Outlaw 525 Owners Manual - Page 134
2007 Polaris Outlaw 525 Manual
Page 134 highlights
Lights Maintenance Headlight Assembly Replacement 6. Install the adjuster bracket onto the inboard pivot pin of the headlamp. Adjust for approximately 1/16" clearance between the bracket and the edge of the headlight. Tighten the mounting screws. IMPORTANT: Be sure the bracket is 90 degrees to the pivot pin so the lamp can move freely. 7. Install the adjusting screw, leaving it loose so the headlight can be adjusted. 8. Reinstall the front cab. Connect the wire harness to the headlamp. 9. Adjust the lamps as needed (see page 128), then tighten the adjuster screw. 131
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129 -
130 -
131 -
132 -
133 -
134 -
135 -
136 -
137 -
138 -
139 -
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
 |
 |
131
Maintenance
Lights
Headlight Assembly Replacement
6.
Install the adjuster bracket onto the inboard pivot pin of the headlamp. Adjust for
approximately 1/16" clearance between the bracket and the edge of the headlight.
Tighten the mounting screws.
IMPORTANT:
Be sure the bracket is 90 degrees to the
pivot pin so the lamp can move freely.
7.
Install the adjusting screw, leaving it loose so the headlight can be adjusted.
8.
Reinstall the front cab. Connect the wire harness to the headlamp.
9.
Adjust the lamps as needed (see page 128), then tighten the adjuster screw.