2011 Kawasaki Brute Force 650 4x4 Owners Manual - Page 114

2011 Kawasaki Brute Force 650 4x4 Manual

Get 2011 Kawasaki Brute Force 650 4x4 PDF manuals and user guides View all 2011 Kawasaki Brute Force 650 4x4 manuals

Page 114 highlights

112 SAFE OPERATION If the water inside transmission is not drained, drain the water in accordance with following procedures. Loosen the air duct clamps to remove the air duct. the bolts to remove the belt drive trans• Loosen mission cover. • Wipe the water off with a clean, lint-free towel. • j A. Air Duct B. Air Duct Clamps the actuator lead connector. • Disconnect • Disconnect the CVT belt indicator lead connector. A. Actuator Lead Connector B. CVT Belt Indicator Lead Connector C. Bolts D. Belt Drive Transmission (CVT) Cover NOTE żBe sure to turn off the ignition switch before dis- the bolts to the specified torque following • Tighten the tightening sequence as shown in the figure. Bolts Tightening Torque: 8.8 N·m (0.90 kgf·m, 78 in·lb) connecting the CVT belt indicator lead connector. If you disconnect the connector with the ignition switch on, the belt indicator light starts flashing. In this case you need to return the vehicle to the dealer for reset.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
112
SAFE OPERATION
j
If the water inside transmission is not drained,
drain the water in accordance with following proce-
dures.
•
Loosen the air duct clamps to remove the air duct.
A. Air Duct
B. Air Duct Clamps
•
Disconnect the actuator lead connector.
•
Disconnect the CVT belt indicator lead connector.
NOTE
°
Be sure to turn off the ignition switch before dis-
connecting the CVT belt indicator lead connector.
If you disconnect the connector with the ignition
switch on, the belt indicator light starts flashing.
In this case you need to return the vehicle to the
dealer for reset.
•
Loosen the bolts to remove the belt drive trans-
mission cover.
•
Wipe the water off with a clean, lint-free towel.
A. Actuator Lead Connector
B. CVT Belt Indicator Lead Connector
C. Bolts
D. Belt Drive Transmission (CVT) Cover
•
Tighten the bolts to the specified torque following
the tightening sequence as shown in the figure.
Bolts Tightening Torque: 8.8 N·m (0.90 kgf·m, 78
in·lb)