Lenovo ThinkServer TD200x Hardware Maintenance Manual for TD200x - Page 142

Power-supply LEDs

Get Lenovo ThinkServer TD200x PDF manuals and user guides View all Lenovo ThinkServer TD200x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

1. Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. 2. If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service technician. Lit EasyLED diagnostics LED with the system-error or information LED also lit Description Action Battery failure LED Battery low. 1. Replace the CMOS lithium battery, if necessary. 2. (Trained service technician only) Replace the system board. IMM heartbeat LED Indicates the status of the boot process of the IMM. When the server is connected to power this LED flashes quickly to indicate that the IMM code is loading. When the loading is complete, the LED stops flashing briefly and then flashes slowly to indicate that the IMM if fully operational and you can press the power-control button to start the server If the LED does not begin flashing within 30 seconds of when the server is connected to power, do the following: 1. (Trained service technician only) Use the IMM recovery switch to recover the firmware (see "System board switches and jumpers" on page 129). 2. (Trained service technician only) Replace the system board. PCI slot 1 to PCI slot 8 error LEDs An error has occurred on a PCI bus or on the system board. An additional LED is lit next to a failing PCI slot. 1. Check the system-event log for information about the error. 2. If you cannot isolate the failing adapter through the LEDs and the information in the system-event log, remove one adapter at a time, and restart the server after each adapter is removed. 3. If the failure remains, call Lenovo Service and Support for additional troubleshooting information. H8 heartbeat LED Indicates the status of power-on and power-off sequencing. 1. If the H8 heartbeat LED is blinking at a 1 Hz rate, no action is necessary. 2. (Trained service technician only) If the H8 heartbeat LED is not blinking, replace the system board. Power-supply LEDs The following illustration shows the power-supply LEDs on the rear of the server. For more information about solving power-supply problems, see "Solving power problems" on page 119. 134 ThinkServer TD200x Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
1. Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.
2. If an action step is preceded by “(Trained service technician only),” that step must be performed only by
a trained service technician.
Lit EasyLED diagnostics LED with the
system-error or information LED also lit
Description
Action
Battery failure LED
Battery low.
1. Replace the CMOS lithium
battery, if necessary.
2. (Trained service technician
only) Replace the system
board.
IMM heartbeat LED
Indicates the status of the boot
process of the IMM.
When the server is connected to
power this LED flashes quickly
to indicate that the IMM code
is loading. When the loading is
complete, the LED stops flashing
briefly and then flashes slowly
to indicate that the IMM if fully
operational and you can press
the power-control button to start
the server
If the LED does not begin flashing
within 30 seconds of when the
server is connected to power, do
the following:
1. (Trained service technician
only) Use the IMM recovery
switch to recover the
firmware (see “System board
switches and jumpers” on
page 129).
2. (Trained service technician
only) Replace the system
board.
PCI slot 1 to PCI slot 8 error LEDs
An error has occurred on a PCI
bus or on the system board. An
additional LED is lit next to a
failing PCI slot.
1. Check the system-event log
for information about the
error.
2. If you cannot isolate the
failing adapter through the
LEDs and the information
in the system-event log,
remove one adapter at
a time, and restart the
server after each adapter is
removed.
3. If the failure remains, call
Lenovo Service and Support
for additional troubleshooting
information.
H8 heartbeat LED
Indicates the status of power-on
and power-off sequencing.
1. If the H8 heartbeat LED is
blinking at a 1 Hz rate, no
action is necessary.
2. (Trained service technician
only) If the H8 heartbeat LED
is not blinking, replace the
system board.
Power-supply LEDs
The following illustration shows the power-supply LEDs on the rear of the server. For more information about
solving power-supply problems, see “Solving power problems” on page 119.
134
ThinkServer TD200x Hardware Maintenance Manual