Icom IC-705 Ci-v Reference Guide english - Page 28

REMOTE CONTROL Remote control (CI-V) information DDCommand formats •• Selected or unselected VFO frequency settings Command: 25 XXXXXX XXXXXX 00=Selected VFO 01=Unselected VFO Operating frequency See "Operating frequency." (p. 17) LLWhen using the DR function, the transceiver returns "FA" (NG) because these cannot be set to 01. •• When VFO A is selected 00=frequency of VFO A changes 01=frequency of VFO B changes •• When VFO B is selected 00=frequency of VFO B changes 01=frequency of VFO A changes •• Selected or unselected VFO's operating mode and filter settings Command: 26 Both data and filter settings can be skipped. In that case, "DATA OFF" and the default filter setting of the operating mode is automatically selected. 2Data mode setting XXXXXXXX 1Operating mode setting 00=Selected VFO 01=Unselected VFO 3Filter setting LLWhen using the DR function, the transceiver returns "FA" (NG) because these cannot be set to 01. •• When VFO A is selected 00 = operating mode of VFO A changes 01 = operating mode of VFO B changes •• When VFO B is selected 00 = operating mode of VFO B changes 01 = operating mode of VFO A changes 1 Operating mode setting 2 Data mode setting 3 Filter setting 00:LSB 05:FM 00: Data mode OFF 01:FIL1 01:USB 06:WFM 01: Data mode ON 02:FIL2 02:AM 07:CW-R - 03:FIL3 03:CW 08:RTTY-R - - 04:RTTY 17:DV - - •• Scope waveform data Command: 27 00 Outputs the waveform data to the controller. 12 34 5 6 7 0 0 X X X X X X X X X X X X X X X X 1: 00 (Fixed) 2: Order of division data (Current): 01~11 3: D ivision number (Maximum): 01(WLAN), 11(USB) LLWhen data is sent to the controller using the WLAN function, all data is sent together. However, when the data is sent through the [microUSB] port, the data is divided by 11 and sent in sequential order. LLThe 1st data sends only the wave information (1 ~ 6) without the waveform data (7). The 2nd or later data sends the minimum wave information (1 ~ 3) with waveform data (7). 4: Spectrum scope mode data: •• 00 = Center mode scope •• 01 = Fixed mode scope •• 02 = SCROLL-C mode scope •• 03 = SCROLL-F mode scope 5: Waveform information: The waveform information differs, depending on the Spectrum scope mode. •• In the Center mode: Center frequency and span are sent. See page 17 for Operating frequency data, and the Scope span settings (2 ~ 6) on page 28. •• In the Fixed, SCROLL-C, and SCROLL-F modes: Lower edge and higher edge frequencies are sent. X X XX X X XX X XX X X X X X X X 0X 10 Hz digit: 0 ~ 9 1 Hz digit: 0 ~ 9 1 kHz digit: 0 ~ 9 100 Hz digit: 0 ~ 9 100 kHz digit: 0 ~ 9 10 kHz digit: 0 ~ 9 10 MHz digit: 0 ~ 9 1 MHz digit: 0 ~ 9 1 GHz digit: 0 , F* 100 MHz digit: 0 ~ 4 10 Hz digit: 0 ~ 9 1 Hz digit: 0 ~ 9 1 kHz digit: 0 ~ 9 100 Hz digit: 0 ~ 9 100 kHz digit: 0 ~ 9 10 kHz digit: 0 ~ 9 10 MHz digit: 0 ~ 9 1 MHz digit: 0 ~ 9 1 GHz digit: 0 (Fixed) 100 MHz digit: 0 ~ 4 Lower edge Higher edge * "F" means that the Lower edge frequency is a negative value. (Continued on the next page.) 27