Icom IC-705 Ci-v Reference Guide english - Page 23

REMOTE CONTROL Remote control (CI-V) information DDCommand formats •• [AUTOTUNE/RX>CS] setting Command: 1A 05 0368 Data Function 00 AUTOTUNE/RX>CS 01 CD/RX>CS 02 PRESET/RX>CS 03 Home CH/RX>CS 04 Temporary Skip/RX>CS •• Alarm area (Group) setting Command: 1A 05 0346 1 2 3 XX X X X 0 10 min� digit: 0 ~ 5 1 min� digit: 0 ~ 9 0�1 min� digit: 0 ~ 9 0�01 min� digit: 0 ~ 9 0�001 min� digit: 0 ~ 9 0 (fixed) •• Manually entered position data Command: 1 A 05 0286, 0312, 0326, 23 02 1 ~ 5 6 ~ 11 12 ~ 15 X X X X X X X X X X X X 1 2 3 4 5 6 7 8 9 10 11 12* 13* 14* 15* XXXXXXX0 0X0XXXXXXXX0 0XXXXXXX0X : •• Data mode with filter width settings Command: 1A 06 12 XX X X 00=Data mode OFF* 01=Data mode ON 01=FIL1 02=FIL2 03=FIL3 *When 00 is set, also set 00 to 2� 10 degree digit: 0 ~ 9 1 degree digit: 0 ~ 9 10 minute digit: 0 ~ 5 1 minute digit: 0 ~ 9 0�1 minute digit: 0 ~ 9 0�01 minute digit: 0 ~ 9 0�001 minute digit: 0 ~ 9 0 (Fixed) 0 (Fixed) South latitude=0/North latitude=1 0 (Fixed) 100 degree digit: 0 ~ 1 10 degree digit: 0 ~ 9 1 degree digit: 0 ~ 9 10 minute digit: 0 ~ 5 1 minute digit: 0 ~ 9 0�1 minute digit: 0 ~ 9 0�01 minute digit: 0 ~ 9 0�001 minute digit: 0 ~ 9 0 (Fixed) 0 (Fixed) West longitude=0/East longitude=1 10000 meter digit: 0 ~ 1 1000 meter digit: 0 ~ 9 100 meter digit: 0 ~ 9 10 meter digit: 0 ~ 9 1 meter digit: 0 ~ 9 0�1 meter digit: 0 ~ 9 0 (Fixed) +=0/-=1 Fixed digit: 0* Fixed digit: 0* 100Hz digit: 0 ~ 2 10 Hz digit: 0 ~ 9 1 Hz digit: 0 ~ 9 0�1 Hz digit: 0 ~ 9 Latitude Longitude Altitude 1 ~ 5: Latitude (dd°mm.mmm format) 6 ~ 11: Longitude (ddd°mm.mmm format) 12 ~ 15: Altitude (0.1 meter steps) * When reading the contents with no altitude, sends 12, 13, 14, and 15 as "FF." * When sending the contents with no altitude, set 12, 13, 14, and 15 to "FF." •• D-PRS Symbol setting Command: 1 A 05 0291 ~ 1A 05 0294, 1A 05 0310, 0324, 0335 XXXX First digit Second digit 0 to 9, A to Z can be used for the first digit character. •• See "Codes for character entries" for the second digit character. (p. 19) •• Repeater tone/tone squelch frequency settings Command: 1B 00, 1B 01 1* 2 3 0 0 X X X X *Not necessary when setting a frequency� •• DTCS code and polarity setting Command: 1B 02 1 2 3 X X 0 X X X 0 (fixed) First digit: 0 ~ 7 Second digit: 0 ~ 7 Third digit: 0 ~ 7 Receive polarity: 0=Normal 1=Reverse Transmit polarity: 0=Normal 1=Reverse 22