Adaptec FS4500 User Guide - Page 45

Installing an I/O Module (or I/O Blank), or FC I/O module.

Get Adaptec FS4500 - Hard Drive Array PDF manuals and user guides
UPC - 760884144275
View all Adaptec FS4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Removing and Replacing Enclosure Components ! Caution: Adaptec highly recommends that you power off the Storage Enclosure before removing or installing any SATA or FC I/O module. SCSI I/O modules are not hot-swappable. 2 Disconnect all the cables connected to the I/O module. 3 Loosen the two screws below the I/O module handles. 4 Gently push down on the handles to disengage the I/O module from the enclosure. 5 Using the handles, gently slide the I/O module out of the enclosure (shown at right). Installing an I/O Module (or I/O Blank) 1 Power off the host system and enclosure. ! Caution: I/O modules are not hot-swappable. You must power off the host system and enclosure before installing an I/O module or I/O blank. 2 Ensure that the handles of the new I/O module are lowered (open). Note: Do not use the handles to lift or carry the I/O module. 3 Gently push up on both handles simultaneously to fix the I/O module into place. 4 Secure the module by tightening the two screws you loosened in Step 3 on page 4-8. Hand-tighten the screws. Do not overtighten them. 5 Connect the I/O cables, as described in the chapter of this Guide that is dedicated to your specific Storage Enclosure's interface: 4-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
4-8
Removing and Replacing Enclosure Components
Caution:
Adaptec
highly recommends
that you power off the
Storage Enclosure before removing or installing any SATA
or FC I/O module.
SCSI I/O modules are
not
hot-swappable.
2
Disconnect all the cables connected to the I/O module.
3
Loosen the two screws below the I/O module handles.
4
Gently push down on the handles
to disengage the I/O module from
the enclosure.
5
Using the handles, gently slide the
I/O module out of the enclosure
(shown at right).
Installing an I/O Module (or I/O Blank)
1
Power off the host system and enclosure.
Caution:
I/O modules are
not
hot-swappable. You must
power off the host system and enclosure before installing
an I/O module or I/O blank.
2
Ensure that the handles of the new I/O module are lowered
(open).
Note:
Do not
use the handles to lift or carry the I/O module.
3
Gently push up on both handles simultaneously to fix the I/O
module into place.
4
Secure the module by tightening the two screws you loosened
in
Step 3 on page 4-8
. Hand-tighten the screws.
Do not
over-
tighten them.
5
Connect the I/O cables, as described in the chapter of this
Guide
that is dedicated to your specific Storage Enclosure’s interface:
!
!