Adaptec FS4500 User Guide - Page 25

Installing into a Tower Assembly, Caution

Get Adaptec FS4500 - Hard Drive Array PDF manuals and user guides
UPC - 760884144275
View all Adaptec FS4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Installing the Storage Enclosure Installing into a Tower Assembly ! Caution: Do not modify the tower assembly. The feet are designed to keep the tower from tipping over. Do not remove the acoustic foam inside the tower skin assembly. 1 If the Storage Enclosure is already set up and running, shut down the enclosure and remove all cables and power cords. You can remove all the drive carriers and both APCs to reduce the weight of the enclosure, if required. If the enclosure is in an equipment rack, remove the two screws holding it in place at the front, then slide the enclosure out of the rack. Remove both the right and left rack mount ear plastic covers (shown at right), as they are no longer needed. (They can be removed by pressing on the plastic inserts from the backside of the rack mount ear or pried off with a screwdriver). 2 Unpack the tower and inspect it for shipping damage. Do not install the enclosure into a damaged or bent tower assembly. 3 Remove the tower's front bezel, as shown in Figure 2-5, saving the screws for use in Step 6. Figure 2-5 Removing the Tower's Front Bezel 4 Turn the enclosure 90° so that the right hand rack mount ear and LEDs are on top. 2-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
2-7
Installing the Storage Enclosure
Installing into a Tower Assembly
Caution:
Do not
modify the tower assembly. The feet are
designed to keep the tower from tipping over. Do not remove
the acoustic foam inside the tower skin assembly.
1
If the Storage Enclosure is already set up and running, shut
down the enclosure and remove all cables and power cords.
You can remove all the drive carriers and both APCs to reduce
the weight of the enclosure, if required.
If the enclosure is in an equipment rack,
remove the two screws holding it in place at
the front, then slide the enclosure out of the
rack. Remove both the right and left rack
mount ear plastic covers (shown at right), as
they are no longer needed. (They can be
removed by pressing on the plastic inserts
from the backside of the rack mount ear or
pried off with a screwdriver).
2
Unpack the tower and inspect it for shipping damage.
Do not
install the enclosure into a damaged or bent tower assembly.
3
Remove the tower’s front bezel, as shown in
Figure 2-5
, saving
the screws for use in
Step 6
.
Figure 2-5
Removing the Tower’s Front Bezel
4
Turn the enclosure 90° so that the right hand rack mount ear
and LEDs are on top.
!