2012 Yamaha Motorsports RS Viking Professional Owners Manual - Page 66

2012 Yamaha Motorsports RS Viking Professional Manual

Get 2012 Yamaha Motorsports RS Viking Professional PDF manuals and user guides View all 2012 Yamaha Motorsports RS Viking Professional manuals

Page 66 highlights

Periodic maintenance and adjustment To adjust the handlebar height 1. Remove the handlebar cover. 1. Handlebar cover 2. Loosen the handlebar bolts. 1. Area where projection cannot be installed 4. 1. Handlebar bolt 3. Move the handlebar up or down to adjust the handlebar height to the desired position. NOTICE: Make sure that the projection on the handlebar is not installed into the area shown. [ECS00571] Tighten the front handlebar bolts to the specified torque, and then tighten the rear handlebar bolts to the specified torque. NOTICE: Make sure each handlebar holder is installed so that the smaller gap is facing forward. [ECS00582] 1. Forward 2. Small gap Handlebar bolt tightening torque: 23 Nm (2.3 m·kgf, 17 ft·lbf) 5. Install the handlebar cover. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Periodic maintenance and adjustment
60
To adjust the handlebar height
1.
Remove the handlebar cover.
2.
Loosen the handlebar bolts.
3.
Move the handlebar up or down to adjust
the handlebar height to the desired posi-
tion.
NOTICE:
Make sure that the pro-
jection on the handlebar is not
installed into the area shown.
[ECS00571]
4.
Tighten the front handlebar bolts to the
specified torque, and then tighten the
rear handlebar bolts to the specified
torque.
NOTICE:
Make sure each han-
dlebar holder is installed so that the
smaller gap is facing forward.
[ECS00582]
5.
Install the handlebar cover.
1.
Handlebar cover
1.
Handlebar bolt
1.
Area where projection cannot be installed
1. Forward
2.
Small gap
Handlebar bolt tightening torque:
23 Nm (2.3 m·kgf, 17 ft·lbf)