2012 Yamaha Motorsports Apex SE Owners Manual - Page 84

2012 Yamaha Motorsports Apex SE Manual

Get 2012 Yamaha Motorsports Apex SE PDF manuals and user guides View all 2012 Yamaha Motorsports Apex SE manuals

Page 84 highlights

Periodic maintenance and adjustment 1 beam adjusting screw in direction (a). To raise the headlight beams, turn the headlight beam adjusting screw in direction (b). 2 1. Slot 2. Projection (b) 1 (a) 14. Fit the weatherstrip on the headlight unit into the recess in the top of the air filter case cover. 1. Headlight beam adjusting screw 3. Install the top cover. 1 ESU12290 Fittings and fasteners Check the tightness of the fittings and fasteners. Tighten in proper sequence and torque if necessary. ESU14020 Battery 1. Weatherstrip 15. Install the headlight unit bolts, and then tighten them to the specified torque. Tightening torque: Headlight unit bolt: 3.0 Nm (0.30 m·kgf, 2.2 ft·lbf) 16. Install the top cover, the left and right side covers, and the shroud. ESU12270 The battery is located under the air filter case. (See page 79.) This model is equipped with a VRLA (Valve Regulated Lead Acid) battery. There is no need to check the electrolyte or to add distilled water. However, the battery lead connections need to be checked and, if necessary, tightened. EWS00540 WARNING Battery electrolyte is poisonous and dangerous. It contains sulfuric acid and can cause severe burns. Avoid contact with skin, eyes, or clothing. ANTIDOTE: G EXTERNAL: Flush with water. Adjusting the headlight beams 1. 2. Remove the top cover. (See page 50 for removal procedures.) Use a Phillips screwdriver to turn the headlight beam adjusting screw and adjust the headlight beams. To lower the headlight beams, turn the headlight 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Periodic maintenance and adjustment
78
14.
Fit the weatherstrip on the headlight unit
into the recess in the top of the air filter
case cover.
15. Install the headlight unit bolts, and then
tighten them to the specified torque.
16.
Install the top cover, the left and right side
covers, and the shroud.
ESU12270
Adjusting the headlight beams
1.
Remove the top cover. (See page 50 for
removal procedures.)
2.
Use a Phillips screwdriver to turn the
headlight beam adjusting screw and ad-
just the headlight beams. To lower the
headlight beams, turn the headlight
beam adjusting screw in direction (a). To
raise the headlight beams, turn the head-
light beam adjusting screw in direction
(b).
3.
Install the top cover.
ESU12290
Fittings and fasteners
Check the tightness of the fittings and fasten-
ers.
Tighten in proper sequence and torque if nec-
essary.
ESU14020
Battery
The battery is located under the air filter case.
(See page 79.)
This model is equipped with a VRLA (Valve
Regulated Lead Acid) battery. There is no
need to check the electrolyte or to add distilled
water. However, the battery lead connections
need to be checked and, if necessary, tight-
ened.
WARNING
EWS00540
Battery electrolyte is poisonous and dan-
gerous. It contains sulfuric acid and can
cause severe burns. Avoid contact with
skin, eyes, or clothing.
ANTIDOTE:
●
EXTERNAL: Flush with water.
1. Slot
2. Projection
1. Weatherstrip
Tightening torque:
Headlight unit bolt:
3.0 Nm (0.30 m·kgf, 2.2 ft·lbf)
1
2
1
1.
Headlight beam adjusting screw
1
(a)
(b)