2010 Yamaha Motorsports TMAX Owners Manual - Page 60

2010 Yamaha Motorsports TMAX Manual

Get 2010 Yamaha Motorsports TMAX PDF manuals and user guides View all 2010 Yamaha Motorsports TMAX manuals

Page 60 highlights

PERIODIC MAINTENANCE AND ADJUSTMENT 11. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. 12. Turn the engine off, and then check the oil level and correct it if necessary. 13. Reset the oil change indicator. (See page 4-6.) TIP If the engine oil is changed before the oil change indicator comes on (i.e. before the periodic oil change interval has been reached), the indicator must be reset after the oil change for the next periodic oil change to be indicated at the correct time. EAU19997 Chain drive oil 3 1 5. Install the chain drive oil drain bolt and its new gasket, and then tighten the bolt to the specified torque. Tightening torque: Chain drive oil drain bolt: 20 Nm (2.0 m·kgf, 14.5 ft·lbf) 1 2 3 4 5 6 7 8 9 2 6. Refill with the specified amount of the recommended oil. Recommended chain drive oil: See page 9-1. Oil quantity: 0.70 L (0.74 US qt, 0.62 Imp.qt) 1. Chain drive oil filler cap 2. Chain drive oil drain bolt 3. Gasket The chain drive oil should be changed as follows at the intervals specified in the periodic maintenance and lubrication chart. 1. Place the vehicle on a level surface. 2. Remove panel E. (See page 7-8.) 3. Place an oil pan under the chain drive case to collect the used oil. 4. Remove the chain drive oil filler cap, the chain drive oil drain bolt and its gasket to drain the oil from the chain drive case. 7-15 7. Wipe the dipstick clean, insert it into the oil filler hole (without screwing it in), and then remove it to check the oil level. TIP The chain drive oil should be between the tip of the dipstick and the maximum level mark.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
PERIODIC MAINTENANCE AND ADJUSTMENT
7-15
1
2
3
4
5
6
7
8
9
11. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
12. Turn the engine off, and then
check the oil level and correct it if
necessary.
13. Reset the oil change indicator.
(See page 4-6.)
TIP
If the engine oil is changed before the
oil change indicator comes on (i.e. be-
fore the periodic oil change interval has
been reached), the indicator must be
reset after the oil change for the next
periodic oil change to be indicated at
the correct time.
EAU19997
Chain drive oil
The chain drive oil should be changed
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place the vehicle on a level sur-
face.
2. Remove panel E. (See page 7-8.)
3. Place an oil pan under the chain
drive case to collect the used oil.
4. Remove the chain drive oil filler
cap, the chain drive oil drain bolt
and its gasket to drain the oil from
the chain drive case.
5. Install the chain drive oil drain bolt
and its new gasket, and then tight-
en the bolt to the specified torque.
6. Refill with the specified amount of
the recommended oil.
7. Wipe the dipstick clean, insert it
into the oil filler hole (without
screwing it in), and then remove it
to check the oil level.
TIP
The chain drive oil should be between
the tip of the dipstick and the maximum
level mark.
1.
Chain drive oil
fi
ller cap
2.
Chain drive oil drain bolt
3. Gasket
1
2
3
Tightening torque:
Chain drive oil drain bolt:
20 Nm (2.0 m
·
kgf, 14.5 ft
·
lbf)
Recommended chain drive oil:
See page 9-1.
Oil quantity:
0.70 L (0.74 US qt, 0.62 Imp.qt)