2008 Yamaha Motorsports Apex M-TX Owners Manual - Page 66

2008 Yamaha Motorsports Apex M-TX Manual

Get 2008 Yamaha Motorsports Apex M-TX PDF manuals and user guides View all 2008 Yamaha Motorsports Apex M-TX manuals

Page 66 highlights

Periodic maintenance 9. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 1 . Secondary sliding sheave 2. Secondary fixed sheave 10. Install the V-belt between the secondary sliding and fixed sheaves. 1 . V-belt position adjusting bolt 2. Spacer V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer 1 . V-belt Not necessary (It is correct.) 11. Install the drive guard, and then install the left side cover and the shroud. ESU12100 Drive chain housing Add spacer EWS00430 7. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lb) The engine, oil tank, brake disc, and coolant hoses will be very hot after the engine has been run. Avoid contact while they are still hot with any part of your body or clothing during inspection or repair. To check the drive chain housing oil level 1. Place the snowmobile on a level surface. 8. Install the V-belt over the primary sheave assembly. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance
1.
V-belt position adjusting bolt
2.
Spacer
V-belt position
More than 1.5 mm
(0.06 in) above the
edge
From 1.5 mm (0.06 in)
above the edge to 0.5
mm (0.02 in) below
the edge
More than 0.5 mm
(0.02 in) below the
edge
Adjustment
Remove spacer
Not necessary (It is
correct.)
Add spacer
7.
Tighten the V-belt position adjusting
bolts.
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lb)
8.
Install the V-belt over the primary sheave
assembly.
9.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
1.
Secondary sliding sheave
2.
Secondary fixed sheave
10.
Install the V-belt between the secondary
sliding and fixed sheaves.
1.
V-belt
11.
Install the drive
guard,
and then install the
left side cover and the shroud.
ESU12100
EWS00430
Drive chain housing
The engine, oil tank, brake disc, and cool-
ant hoses will be very hot after the engine
has been run. Avoid contact while they are
still hot with any part of your body or cloth-
ing during inspection or repair.
To check the drive chain housing oil level
1.
Place the snowmobile on a level surface.
60