2008 Yamaha Motorsports Apex M-TX Owners Manual - Page 19

2008 Yamaha Motorsports Apex M-TX Manual

Get 2008 Yamaha Motorsports Apex M-TX PDF manuals and user guides View all 2008 Yamaha Motorsports Apex M-TX manuals

Page 19 highlights

Control functions and then push the "SELECT" button for at least 10 seconds while the snowmobile is stopped. • To switch the barometer display between hectopascal "hPa" and inches of mercury "inHg", select the barometer mode "BARO", and then push the "SELECT" button for at least 3 seconds while the snowmobile is stopped. 3. Push the "RESET" button to change the minute setting, and then push the "SELECT" button. The clock starts when the "SELECT" button is released. NOTE: The clock must be set again when the battery is disconnected. Display brightness control This function allows you to adjust the brightness of the meter display to suit the outdoor lighting conditions. To adjust the display brightness 1. Turn the main switch to the off position. 2. Push and hold down the "SELECT" button. Clock To set the clock 1. Push the "SELECT" button and "RESET" button simultaneously until the hour digits start flashing. 1 . "SELECT" button 2. "RESET" button 3. Display brightness level 3. 4. 1 . "SELECT" button 2. "RESET" button Turn the main switch to the on position, and then, after 5 seconds, release the "SELECT" button. Push the "RESET" button to select the desired display brightness level, and then push the "SELECT" button. The normal display returns when the "SELECT" button is released. 2. Push the "RESET" button to change the hour setting, and then push the "SELECT" button. The minute digits will start flashing. NOTE: If the main switch is turned to the off position or the engine is started before completing the procedure, the setting is not applied. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
and then push the “SELECT” button for at
least 10 seconds while the snowmobile is
stopped.
• To switch the barometer display between
hectopascal “hPa” and inches of mercury
“inHg”,
select the barometer mode “BARO”,
and then push the “SELECT” button for at
least 3 seconds while the snowmobile is
stopped.
Clock
To set the clock
1.
Push the “SELECT” button and “RESET”
button simultaneously until the hour digits
start flashing.
1.
“SELECT” button
2.
“RESET” button
2.
Push the “RESET” button to change the
hour setting, and then push the “SE-
LECT”
button.
The minute digits will start
flashing.
Control functions
3.
Push the “RESET” button to change the
minute setting, and then push the “SE-
LECT” button. The clock starts when the
“SELECT” button is released.
NOTE:
The clock must be set again when the battery
is disconnected.
Display brightness control
This function allows you to adjust the bright-
ness of the meter display to suit the outdoor
lighting conditions.
To adjust the display brightness
1.
Turn the main switch to the off position.
2.
Push and hold down the “SELECT” but-
ton.
1.
“SELECT” button
2.
“RESET” button
3. Display brightness level
3.
Turn the main switch to the on position,
and
then,
after 5 seconds, release the
“SELECT” button.
4.
Push the “RESET” button to select the
desired display brightness
level,
and then
push the “SELECT” button. The normal
display returns when the “SELECT” but-
ton is released.
NOTE:
If the main switch is turned to the off position
or the engine is started before completing the
procedure, the setting is not applied.
13