2006 Polaris 600 Switchback Owners Manual - Page 61

2006 Polaris 600 Switchback Manual

Page 61 highlights

OPERATION Starting the Engine Starting a Warm Engine 1. Turn the key to the ON position. 2. Pull the engine stop switch up to the RUN position. 3. Grasp the recoil rope handle and pull slowly until the recoil engages; then pull abruptly. NOTE: If the engine does not start on the first pull, slightly depress the throttle with your left hand (no more than 1/4" open), and pull the rope with your right hand. When the engine starts, immediately release the throttle. Engine Break-In No single action on your part is as important to long, trouble-free machine life as proper break-in of a new or rebuilt engine. Premix the first tank of gasoline with one pint of Polaris injection oil for each five gallons of fuel. This, in addition to the lubrication supplied by the injection system, will assure proper engine break-in. CAUTION Excessive heat build-up during the first three hours of operation will damage close-fitted engine parts. Do not operate at full throttle or high speeds for extended periods during the first three hours of use. Vary the throttle openings and machine speeds to reduce friction on all close-fitting machined parts, allowing them to break in slowly without damage. Use of any lubricants other than those recommended by Polaris may cause serious engine damage. We recommend the use of Polaris lubricants for your vehicle. Drive with extra caution during the break-in period. Perform regular checks on fluid levels, lines, and all other important areas of the machine. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127

58
OPERATION
Starting the Engine
Starting a Warm Engine
1.
Turn the key to the
ON
position.
2.
Pull the engine stop switch up to the
RUN
position.
3.
Grasp the recoil rope handle and pull slowly until the recoil
engages; then pull abruptly.
NOTE:
If the engine does not start on the first pull, slightly depress
the throttle with your left hand (no more than 1/4” open), and
pull the rope with your right hand. When the engine starts,
immediately
release the throttle.
Engine Break-In
No single action on your part is as important to long, trouble-free
machine life as proper break-in of a new or rebuilt engine. Premix the
first tank of gasoline with one pint of Polaris injection oil for each five
gallons of fuel. This, in addition to the lubrication supplied by the
injection system, will assure proper engine break-in.
CAUTION
Excessive heat build-up during the first three hours of operation
will damage close-fitted engine parts. Do not operate at full
throttle or high speeds for extended periods during the first three
hours of use. Vary the throttle openings and machine speeds to
reduce friction on all close-fitting machined parts, allowing them
to break in slowly without damage.
Use of any lubricants other than those recommended by Polaris
may cause serious engine damage. We recommend the use of
Polaris lubricants for your vehicle.
Drive with extra caution during the break-in period. Perform
regular checks on fluid levels, lines, and all other important areas
of the machine.