2006 Polaris 600 Switchback Owners Manual - Page 103

2006 Polaris 600 Switchback Manual

Get 2006 Polaris 600 Switchback PDF manuals and user guides View all 2006 Polaris 600 Switchback manuals

Page 103 highlights

MAINTENANCE Track Maintenance n Track Alignment Periodically check that the track is centered and running evenly on the slide rails. Misalignment will cause excessive wear to the track and slide rail. 1. Safely support the rear of the machine with the track off the ground. 2. Start the engine and apply a small amount of throttle until the track turns slowly at least five complete revolutions. Stop the engine and let the track come to a + stop (do not apply brakes). 3. Inspect track alignment by looking through the track window to make sure the rails (+) are evenly spaced on each side. If the track runs to the left, loosen left locknut and tighten the left adjusting bolt. If the track runs to the right, loosen right locknut and tighten the right adjusting bolt. 4. After adjustments are complete, tighten locknuts and torque idler shaft bolts to 35 ft. lbs. (47.5 Nm). 5. Repeat steps 2 and 3 to verify proper alignment. 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
+
100
MAINTENANCE
Track Maintenance
n
Track Alignment
Periodically check that the track
is centered and running evenly
on the slide rails. Misalignment
will cause excessive wear to the
track and slide rail.
1.
Safely support the rear of the
machine with the track off
the ground.
2.
Start the engine and apply a
small amount of throttle
until the track turns
slowly
at
least five complete
revolutions. Stop the engine
and let the track come to a
stop (do not apply brakes).
3.
Inspect track alignment by looking through the track window to
make sure the rails (
+
) are evenly spaced on each side. If the track
runs to the left, loosen left locknut and tighten the left adjusting
bolt. If the track runs to the right, loosen right locknut and tighten
the right adjusting bolt.
4.
After adjustments are complete, tighten locknuts and torque idler
shaft bolts to 35 ft. lbs. (47.5 Nm).
5.
Repeat steps 2 and 3 to verify proper alignment.