Schwinn 290 Recumbent Bike 2021 model Service Manual - Page 98

The Left Pedal is reverse-threaded., Slide Crank Disc off Crank Arm Schwinn, crank arm shown

Get Schwinn 290 Recumbent Bike 2021 model PDF manuals and user guides View all Schwinn 290 Recumbent Bike 2021 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

8. Using a pedal wrench or 15mm open end wrench, loosen and remove the Pedal. Set it safely aside for reassembly. Note: The Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 9. Turn the Crank Arm to point up toward the rear of the bike. Carefully angle the Crank Disc and slide it over the Crank Arm. Set it safely aside. Slide Crank Disc off Crank Arm (Schwinn™ 190 crank arm shown) 10. Install the new Crank Discs. Be sure the Crank Arm points up toward the front of the bike. Carefully angle the new Crank Disc and slide it over the Crank Arm into position. 11. To install the Main Shrouds, put the Left Shroud in SRVLWLRQ¿UVWWRDOLJQWKHVFUHZVDQGLQWHUQDO6KURXG,QVHUW for the Right Shroud. Be sure the Crank Arm points up toward the rear of the bike. Carefully angle the new Main Shroud and slide it over the Crank Arm into position. NOTICE: Be sure not to pinch or cut any cables. 12. Using a #2 Phillips Screwdriver, attach the Crank Disc to WKH0DLQ6KURXG,QVWDOOWKHWRSVFUHZV¿UVW 13. Repeat steps 10 and 11 for the Right Shroud. 14. Using a #2 Phillips Screwdriver, attach the Main 6KURXGV,QVWDOOWKHWRSVFUHZV¿UVW 98

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
98
8.
Using a pedal wrench or 15mm open end wrench,
loosen and remove the Pedal. Set it safely aside for
reassembly.
Note:
The Left Pedal is reverse-threaded.
Orientation is
based from a seated position on the bike. The Left
Pedal has an “L”, the Right Pedal an “R”.
(L)
(R)
Slide Crank Disc off Crank Arm (Schwinn
™
190 crank arm shown)
9.
Turn the Crank Arm to point up toward the rear of the
bike. Carefully angle the Crank Disc and slide it over the
Crank Arm. Set it safely aside.
10.
Install the new Crank Discs. Be sure the Crank Arm
points up toward the front of the bike. Carefully angle the
new Crank Disc and slide it over the Crank Arm into position.
11.
To install the Main Shrouds, put the Left Shroud in
SRVLWLRQ ¿UVW WR DOLJQ WKH VFUHZV DQG LQWHUQDO 6KURXG ,QVHUW
for the Right Shroud.
Be sure the Crank Arm points up toward the rear of the bike.
Carefully angle the new Main Shroud and slide it over the
Crank Arm into position.
NOTICE:
Be sure not to pinch or cut any cables.
12.
Using a #2 Phillips Screwdriver, attach the Crank Disc to
WKH 0DLQ 6KURXG³ ,QVWDOO WKH WRS VFUHZV ¿UVW³
13.
Repeat steps 10 and 11 for the Right Shroud.
14.
Using a #2 Phillips Screwdriver, attach the Main
6KURXGV³ ,QVWDOO WKH WRS VFUHZV ¿UVW³