Schwinn 290 Recumbent Bike 2021 model Service Manual - Page 92

Lulqj Kduqhvv, Lulqj Kdu

Get Schwinn 290 Recumbent Bike 2021 model PDF manuals and user guides View all Schwinn 290 Recumbent Bike 2021 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

9. Carefully disconnect the Servo Motor cable from the wiring harness. NOTICE: Do not pinch or cut the cables. 6HUYRPRWRUFDEOHDQGZLULQJKDUQHVVFRQQHFWRUV Servo cable connector 10. Using a #2 Phillips Screwdriver, remove the 3 screws (indicated with ovals) that attach the Servo Motor to the Main Frame. Set them safely aside for reassembly. Carefully remove the old Servo Motor assembly and discard. NOTICE: Do not pinch or cut the cables. :LULQJKDUness :LULQJKDUQHVV connector Servo motor 11. Before installing the new Servo Motor, inspect it to be sure that the Servo Motor arm is in the correct position as shown. Servo motor arm position NOTICE: The angle between the Servo Motor arm and Servo top should be 20° (+3/-0). If the arm is not in the correct position. it could cause the linkage to roll over the wrong way and jam during operation. Servo motor top 20° Servo motor arm 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
92
10.
Using a #2 Phillips Screwdriver, remove the 3 screws
(indicated with ovals) that attach the Servo Motor to the
Main Frame. Set them safely aside for reassembly. Carefully
remove the old Servo Motor assembly and discard.
NOTICE:
Do not pinch or cut the cables.
11.
Before installing the new Servo Motor, inspect it to be
sure that the Servo Motor arm is in the correct position as
shown.
NOTICE:
The angle between the Servo Motor arm and
Servo top should be 20° (+3/-0). If the arm is
not in the correct position. it could cause the
linkage to roll over the wrong way and jam
during operation.
9.
Carefully disconnect the Servo Motor cable from the wir-
ing harness.
NOTICE:
Do not pinch or cut the cables.
6HUYR PRWRU FDEOH DQG ZLULQJ KDUQHVV FRQQHFWRUV
Servo cable
Servo cable
connecto
connecto
r
:LULQJ KDUQHVV
:LULQJ KDUQHVV
connector
connector
:LULQJ KDU
-
:LULQJ KDU
-
ness
ness
Servo
Servo
motor
motor
20
°
Servo motor arm position
Servo
motor
arm
Servo motor top