Panasonic PT-EX520 Operating Instructions - Page 95

[RS-232C]

Get Panasonic PT-EX520 PDF manuals and user guides View all Panasonic PT-EX520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Chapter 4 Settings - [PROJECTOR SETUP] menu ffThe [ECO MANAGEMENT] screen is displayed. 3) Press as to select [STANDBY MODE]. 4) Press qw to switch the item. ffThe items will switch each time you press the button. [NORMAL] [ECO] Select this item to use the network function or the serial communication function during standby. Select this item to reduce power consumption during standby. Note ff If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannot use some RS232C protocol commands. ff When set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on, compared with when [NORMAL] is set. ff When set to [NORMAL], it may take approx. 1 minute to enable the network function after connecting the power cord. ff The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu → [INITIALIZE ALL] is executed. (Æ page 103) [RS-232C] Set the communication conditions of the terminal. Setting the communication condition of the terminal 1) Press as to select [RS-232C]. 2) Press the button. ffThe [RS-232C] screen is displayed. ffOnly for PT-EW550 and PT-EX520, proceed to step 5). 3) Press as to select [INPUT SELECT]. 4) Press qw to switch the item. [PROJECTOR] [DIGITAL LINK] Use the terminal of the projector to perform RS‑232C communication. Performs RS‑232C communication via the DIGITAL LINK output supported device (Model No.: ET‑YFB100G, ET‑YFB200G) and the terminal. 5) Press as to select [BAUDRATE]. 6) Press qw to switch the item. ffThe items will switch each time you press the button. [9600] [19200] [38400] Select the proper speed. 7) Press as to select [PARITY]. 8) Press qw to switch the item. ffThe items will switch each time you press the button. [NONE] [EVEN] [ODD] Select the parity condition. Setting the control commands of an existing projector When controlling the projector on a computer, set use of control commands on a previously purchased Panasonic projector. This allows the control software for an existing Panasonic projector to be inherited and used. 1) Press as to select [RS-232C]. 2) Press the button. ffThe [RS-232C] screen is displayed. ENGLISH - 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Chapter 4
Settings — [PROJECTOR SETUP] menu
ENGLISH - 95
f
The
[ECO MANAGEMENT]
screen is displayed.
3)
Press
as
to select [STANDBY MODE].
4)
Press
qw
to switch the item.
f
The items will switch each time you press the button.
[NORMAL]
Select this item to use the network function or the serial communication function during standby.
[ECO]
Select this item to reduce power consumption during standby.
Note
f
If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannot use some RS-
232C protocol commands.
f
When set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on, compared with
when [NORMAL] is set.
f
When set to [NORMAL], it may take approx. 1 minute to enable the network function after connecting the power cord.
f
The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu → [INITIALIZE ALL] is
executed. (
Æ
page 103)
[RS-232C]
Set the communication conditions of the <SERIAL IN> terminal.
Setting the communication condition of the <SERIAL IN> terminal
1)
Press
as
to select [RS-232C].
2)
Press the <ENTER> button.
f
The
[RS-232C]
screen is displayed.
f
Only for PT-EW550 and PT-EX520, proceed to step
5)
.
3)
Press
as
to select [INPUT SELECT].
4)
Press
qw
to switch the item.
[PROJECTOR]
Use the <SERIAL IN> terminal of the projector to perform RS-232C communication.
[DIGITAL LINK]
Performs RS-232C communication via the DIGITAL LINK output supported device (Model No.:
ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.
5)
Press
as
to select [BAUDRATE].
6)
Press
qw
to switch the item.
f
The items will switch each time you press the button.
[9600]
Select the proper speed.
[19200]
[38400]
7)
Press
as
to select [PARITY].
8)
Press
qw
to switch the item.
f
The items will switch each time you press the button.
[NONE]
Select the parity condition.
[EVEN]
[ODD]
Setting the control commands of an existing projector
When controlling the projector on a computer, set use of control commands on a previously purchased Panasonic
projector. This allows the control software for an existing Panasonic projector to be inherited and used.
1)
Press
as
to select [RS-232C].
2)
Press the <ENTER> button.
f
The
[RS-232C]
screen is displayed.