Panasonic PT-EX520 Operating Instructions - Page 141

Replacing the unit

Get Panasonic PT-EX520 PDF manuals and user guides View all Panasonic PT-EX520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 141 highlights

Chapter 6 Maintenance - Maintenance/replacement Replacing the unit Lamp unit The lamp unit is a consumable component. Refer to "When to replace the lamp unit" (x page 141) for details about the replacement cycle. When purchasing the optional Replacement Lamp Unit (Model No.: ET‑LAEF100), consult your dealer. It is recommended that you request a qualified technician to replace the lamp unit. Consult your dealer. WARNING Replace the lamp unit after the lamp has cooled (after waiting at least one hour). The high temperature inside the cover will cause burns. Notes on the replacement of the lamp unit ffSince the luminous lamp is made of glass, it may burst if dropped or hit with a hard object. Handle with care. ffDo not disassemble or modify the lamp unit. ffWhen replacing the lamp unit, be sure to hold it by the handle because its surface is pointed and its shape is protruded. ffThe lamp may rapture. Replace the lamp unit carefully so that the glass fragments of the lamp do not scatter. While attaching the projector to the ceiling, do not work right under the lamp unit or do not conduct work while your face is near the lamp unit. ffThe lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct methods of disposal. Attention ff Panasonic takes no responsibility for any damage or malfunction of the product resulting from use of lamp units which are not manufactured by Panasonic. Use only specified lamp units. Note ff The model numbers of accessories and optional accessories are subject to change without prior notice. ff A Phillips screwdriver is necessary when replacing the lamp unit. When to replace the lamp unit The lamp unit is a consumable component. Since its brightness gradually decreases over time, it is necessary to replace the lamp unit regularly. Time for replacement When [LAMP POWER] is constantly set to [NORMAL] without switching to other modes = 4 000 hours When [LAMP POWER] is constantly set to [ECO] without switching to other modes = 5 000 hours but the lamp may go off before the time above mentioned has elapsed depending on individual lamp characteristics, usage conditions, and the installation environment. It is recommended that the Replacement lamp unit be prepared earlier. In order to predict the lamp replacement time, please refer to the lamp runtime displayed in [STATUS] (x page 92) → [RUNTIME] → [LAMP] → [NORMAL]/[ECO]. It also can be obtained by using the following formula. (The time which is displayed in [ECO] is the converted usage time when set to [NORMAL].) Formula for lamp replacement time (rough estimate) = "Lamp runtime of [NORMAL]" + "Lamp runtime of [ECO]" × 4/5 If the time which is obtained by the above equation 4 000 hours has elapsed, the lamp turns off automatically after approximately 10 minutes, as it will cause malfunction of the projector. ENGLISH - 141

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Chapter 6
Maintenance — Maintenance/replacement
ENGLISH - 141
Replacing the unit
Lamp unit
The lamp unit is a consumable component. Refer to “When to replace the lamp unit” (
x
page 141) for details
about the replacement cycle.
When purchasing the optional Replacement Lamp Unit (Model No.: ET-LAEF100), consult your dealer.
It is recommended that you request a qualified technician to replace the lamp unit. Consult your dealer.
WARNING
Replace the lamp unit after the lamp has cooled (after waiting at least one hour).
The high temperature inside the cover will cause burns.
Notes on the replacement of the lamp unit
f
Since the luminous lamp is made of glass, it may burst if dropped or hit with a hard object. Handle with care.
f
Do not disassemble or modify the lamp unit.
f
When replacing the lamp unit, be sure to hold it by the handle because its surface is pointed and its shape is
protruded.
f
The lamp may rapture. Replace the lamp unit carefully so that the glass fragments of the lamp do not scatter.
While attaching the projector to the ceiling, do not work right under the lamp unit or do not conduct work while
your face is near the lamp unit.
f
The lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for
correct methods of disposal.
Attention
f
Panasonic takes no responsibility for any damage or malfunction of the product resulting from use of lamp units which are not manufactured
by Panasonic. Use only specified lamp units.
Note
f
The model numbers of accessories and optional accessories are subject to change without prior notice.
f
A Phillips screwdriver is necessary when replacing the lamp unit.
When to replace the lamp unit
The lamp unit is a consumable component. Since its brightness gradually decreases over time, it is necessary to
replace the lamp unit regularly.
Time for replacement
When [LAMP POWER] is constantly set to [NORMAL] without switching to other modes = 4 000 hours
When [LAMP POWER] is constantly set to [ECO] without switching to other modes = 5 000 hours
but the lamp may go off before the time above mentioned has elapsed depending on individual lamp
characteristics, usage conditions, and the installation environment. It is recommended that the Replacement lamp
unit be prepared earlier.
In order to predict the lamp replacement time, please refer to the lamp runtime displayed in [STATUS]
(
x
page 92) → [RUNTIME] → [LAMP] → [NORMAL]/[ECO]. It also can be obtained by using the following
formula. (The time which is displayed in [ECO] is the converted usage time when set to [NORMAL].)
Formula for lamp replacement time (rough estimate) = “Lamp runtime of [NORMAL]” + “Lamp runtime of
[ECO]” × 4/5
If the time which is obtained by the above equation 4 000 hours has elapsed, the lamp turns off automatically after
approximately 10 minutes, as it will cause malfunction of the projector.