LiftMaster RSL12U RSL12U Installation Manual - Page 29

Locks, Miscellaneous Wiring

Get LiftMaster RSL12U PDF manuals and user guides View all LiftMaster RSL12U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

ACCESSORY WIRING LOCKS MAGLOCK (2 Terminals, N.C. and COM) Relay contact output, Normally - closed (N.C.) output for maglocks. Relay activates prior to motor activation and during motor run. Relay is off when motor is off. (control board) SOLENOID (2 Terminals, N.O. and COM) Normally - open (N.O.) output for solenoid locks Relay activates prior to motor activation and during motor run. Relay is off when motor is off. NOTE: To conserve power for solar applications, the lock relay will only activate for four seconds near the close limit. (control board) Maglock _ + (not provided) Solenoid Lock _ + (not provided) MISCELLANEOUS WIRING THREE BUTTON CONTROL STATION (4 Terminals) • OPEN and COM: Opens a closed gate. Hard open (maintained switch overrides external safeties and resets alarm condition). If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate (within line-of-sight). • CLOSE and COM: Closes an open gate. Hard close (maintained switch overrides external safeties and resets alarm condition within line-of-sight) • STOP and COM: Stops a moving gate. Hard stop (maintained switch overrides Open and Close commands and resets alarm condition). If maintained, pauses Timer-to-Close at OPEN limit. Overrides Open and Close commands (within line-of-sight). FIRE DEPARTMENT OPEN INPUT (2 Terminals) Acts as hard open. Maintained input overrides (ignores) external safeties (photoelectric sensor and edge), pauses Timer-to-Close momentary input logic as single button control and safeties remain active, re-enables Timer-to-Close. ACCESSORY POWER 12 VDC, MAX 500 mA (4 Terminals) • SWITCHED: Switched ON with gate motion (stays on 5 seconds after motion). • UNSWITCHED: 12 Vdc voltage out to power accessories, always ON. 28 (main control board) Three Button Control Station Open Close Stop Com N.C. Fire Dept Com Fire Department (main control board) Accessory Power Switched Com (-) Acc Power +12 Vdc Com (-) Acc Power +12 Vdc Accessory Power Unswitched

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
28
ACCESSORY WIRING
MISCELLANEOUS WIRING
THREE BUTTON CONTROL STATION
(4 Terminals)
•
OPEN and COM:
Opens a closed gate.
Hard open (maintained switch overrides external safeties and resets
alarm condition). If maintained, pauses Timer-to-Close at OPEN limit.
Opens a closing gate and holds open an open gate (within
line-of-sight).
•
CLOSE and COM:
Closes an open gate.
Hard close (maintained switch overrides external safeties and resets
alarm condition within line-of-sight)
•
STOP and COM:
Stops a moving gate.
Hard stop (maintained switch overrides Open and Close commands
and resets alarm condition). If maintained, pauses Timer-to-Close at
OPEN limit. Overrides Open and Close commands (within
line-of-sight).
FIRE DEPARTMENT OPEN INPUT
(2 Terminals)
Acts as hard open.
Maintained input overrides (ignores) external safeties (photoelectric
sensor and edge), pauses Timer-to-Close momentary input logic as single
button control and safeties remain active, re-enables Timer-to-Close.
ACCESSORY POWER 12 VDC, MAX 500 mA
(4 Terminals)
•
SWITCHED:
Switched ON with gate motion (stays on 5 seconds after
motion).
•
UNSWITCHED:
12 Vdc voltage out to power accessories, always ON.
LOCKS
_
+
_
+
Com
Open
(main control board)
Three Button Control Station
Fire Department
Com
Fire Dept
Acc Power +12 Vdc
Com (-)
(main control board)
Maglock
Solenoid Lock
(not provided)
(not provided)
(control board)
(control board)
Accessory Power Unswitched
Accessory Power Switched
Acc Power +12 Vdc
Com (-)
Close
Stop
N.C.
MAGLOCK
(2 Terminals, N.C. and COM)
Relay contact output, Normally - closed (N.C.) output for maglocks.
Relay activates prior to motor activation and during motor run. Relay is
off when motor is off.
SOLENOID
(2 Terminals, N.O. and COM)
Normally - open (N.O.) output for solenoid locks
Relay activates prior to motor activation and during motor run. Relay is
off when motor is off.
NOTE:
To conserve power for solar applications, the lock relay will only
activate for four seconds near the close limit.