LiftMaster 61LM Owners Manual - Page 222

Model 33LM, Multi-Function, Remote Control Transmitter, OWNER'S MANUAL

Get LiftMaster 61LM PDF manuals and user guides View all LiftMaster 61LM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 222 highlights

OWNER'S MANUAL Model 33LM Multi-Function Remote Control Transmitter The 33LM Multi-Function Remote Control Transmitter can be used with a 423LM 3-channel receiver and a 3-button door control to operate a commercial door opener in open, close, and stop mode (as explained on side 1). It can also be used with other transmitters to operate a garage door opener, in which case the code switches in all transmitters must be set to match (see side 2). To comply with FCC/IC rules, adjustment or modification of receiver and/or transmitter is prohibited, except for changing the code setting and replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. To use the transmitter with a 3-channel receiver and 3-button door control to operate a commercial door opener: WARNING Install the control station and receiver where the door is visible, but away from the door and its hardware. When a receiver is used to activate a commercial door opener, a reversing edge MUST be installed on the bottom of the door. Failure to install a reversing edge under these circumstances may result in serious injury or death to persons trapped beneath the door. Use a screwdriver to pry open the receiver cover (see illustration). The slide switch is factory set to the N.C. position (otherwise the opener will not operate). Verify this setting . • Select a remote control push button to STOP the opener. (RED is recommended.) • Press and hold the selected remote push button. • Then press and release the "smart" button labeled "A" on the receiver. The adjacent indicator light will FLASH. Release the remote push button. Repeat the procedure above with the yellow remote push button and receiver "smart" button "B" to program the CLOSE operation; and again with the green remote push button and receiver "smart" button "C" to program the OPEN function of the opener. Return the front cover to the receiver. (For this application, code switch settings need not be changed.) OPENING RECEIVER Connect Antenna CBA Open Close Stop Remote control push buttons Slide Switch - N.C. Position 423LM 3-Channel Receiver Note: If a remote control push button is not pressed within 30 seconds, the indicator light adjacent to the selected "smart" button will turn OFF. In that case, repeat the programming. Side 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
Use a screwdriver to pry open the receiver cover (see
illustration).
The slide switch is factory set to the N.C. position
(otherwise the opener will not operate).
Verify this
setting
.
•
Select a remote control push button to STOP the
opener.
(RED is recommended.)
•
Press and
hold
the selected remote push button.
•
Then press and release the “smart” button labeled
“A” on the receiver. The adjacent indicator light will
FLASH. Release the remote push button.
Repeat the procedure above with the yellow remote
push button and receiver “smart” button “B” to
program the CLOSE operation; and again with the
green remote push button and receiver “smart” button
“C” to program the OPEN function of the opener.
Return the front cover to the receiver.
(For this application, code switch settings need not be
changed.)
Model 33LM
Multi-Function
Remote Control Transmitter
The 33LM Multi-Function Remote Control
Transmitter can be used with a 423LM 3-channel
receiver and a 3-button door control to operate a
commercial door opener in open, close, and stop
mode (as explained on side 1).
It can also be used with other transmitters to
operate a garage door opener, in which case
the
code switches in all transmitters must be set to
match (see side 2).
Install the control station and receiver where
the door is visible, but away from the door
and its hardware. When a receiver is used to
activate a commercial door opener,
a
reversing edge MUST be installed on the
bottom of the door.
Failure to install a
reversing edge under these circumstances
may result in serious injury or death to
persons trapped beneath the door.
To comply with FCC/IC rules, adjustment or modification of
receiver and/or transmitter is prohibited, except for changing the
code setting and replacing the battery. THERE ARE NO OTHER
USER SERVICEABLE PARTS.
A
B
C
OPENING
RECEIVER
Remote control
push buttons
Connect
Antenna
Open
Close
Stop
Slide Switch – N.C. Position
Note: If a remote control push button is not
pressed within 30 seconds, the indicator light
adjacent to the selected “smart” button will turn
OFF. In that case, repeat the programming.
To use the transmitter with a 3-channel receiver and 3-button door control
to operate a commercial door opener:
423LM 3-Channel Receiver
OWNER’S MANUAL
Side 1
WARNING