Icom IC-M37 Instruction Manual - Page 28

Atis Code

Get Icom IC-M37 PDF manuals and user guides View all Icom IC-M37 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

9 ATIS CODE (For only the HOL and FRG versions) The Automatic Transmitter Identification System (ATIS) ID consists of 10 digits. You can set and confirm the ID as shown below. NOTE: You can enter this initial code ONLY ONCE. After entry, only your dealer or distributor can change it. If your ATIS code has already been entered, this entry is not necessary. DDSetting the ATIS code 1. Turn OFF the power. 2. While holding down [16/C], push [ ]. ••Enters to the ATIS Code Setting mode. 3. Push [▲] or [▼] to select the number for the first digit of the ATIS code. 4. Push [CH/WX] to select the next digit, and then push [▲] or [▼] to select a number. ••Pushing [VOL/SQL] selects the previous digit. 5. After the 10th digit has been input, push [Hi/Lo] to store the code. ••The code number stops blinking. ••Push [16/C] to return to the normal operating mode. DDATIS code confirmation (Can be performed only when the ATIS code has been programmed.) 1. Turn OFF the power. 2. While holding down [16/C], push [ ] to enter the ATIS code confirmation mode. ••The stored code number is displayed. ••Push [CH] to select the next digit, push [VOL/SQL] to select the previous digit. 3. Push [16/C] to exit the ATIS Confirmation mode. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
20
9
ATIS CODE
The Automatic Transmitter Identification System (ATIS) ID consists
of 10 digits. You can set and confirm the ID as shown below.
NOTE:
You can enter this initial code ONLY ONCE. After entry,
only your dealer or distributor can change it. If your ATIS code
has already been entered, this entry is not necessary.
D
Setting the ATIS code
1.
Turn OFF the power.
2.
While holding down [16/C], push [
].
• Enters to the ATIS Code Setting mode.
3.
Push [▲] or [▼] to select the number for the first digit of the
ATIS code.
4.
Push [CH/WX] to select the next digit, and then push [▲] or
[▼] to select a number.
• Pushing [VOL/SQL] selects the previous digit.
5.
After the 10th digit has been input, push [Hi/Lo] to store the
code.
• The code number stops blinking.
• Push [16/C] to return to the normal operating mode.
D
ATIS code confirmation
(Can be performed only when the ATIS code has been
programmed.)
1.
Turn OFF the power.
2.
While holding down [16/C], push [
] to enter the ATIS code
confirmation mode.
• The stored code number is displayed.
• Push [CH] to select the next digit, push [VOL/SQL] to select
the previous digit.
3.
Push [16/C] to exit the ATIS Confirmation mode.
(For only the HOL and FRG versions)