Dell Latitude 7280 Owners Manual - Page 29

Installing display assembly—with touch, Installing display bezel

Get Dell Latitude 7280 PDF manuals and user guides View all Dell Latitude 7280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Installing display assembly-with touch 1. Place the base of the computer on a plane surface of a table and position it closer to the edge of the table. 2. Install the display assembly to align it with the display hinge holders on the system. 3. Holding the display assembly, tighten the M2.5 x 4.0 screws to secure the display hinges on the system display assembly with the system unit. 4. Affix the tapes to secure the eDP cable (display cable). 5. Connect the eDP cable to the connector on the system board. 6. Install the eDP metal bracket on the eDP cable and tighten the M2.0 x 5.0 screws. 7. Route the WLAN and WWAN cables through the routing channels. 8. Install the: a. WLAN card b. WWAN card c. battery d. base cover 9. Follow the procedure in After working inside your computer. Installing display bezel NOTE: The display bezel installation procedure is applicable only for non-touch systems. 1. Place the display bezel on the display assembly. 2. Press the edges of the display bezel until it clicks onto the display assembly. NOTE: Adhesive is used to secure the display bezel to the display panel. 3. Install the: a. display assembly b. WLAN card c. WWAN card d. battery e. base cover 4. Follow the procedure in After working inside your computer. Disassembly and reassembly 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Installing display assembly—with touch
1.
Place the base of the computer on a plane surface of a table and position it closer to the edge of the table.
2.
Install the display assembly to align it with the display hinge holders on the system.
3.
Holding the display assembly, tighten the M2.5 x 4.0 screws to secure the display hinges on the system display assembly with the
system unit.
4.
Affix the tapes to secure the eDP cable (display cable).
5.
Connect the eDP cable to the connector on the system board.
6.
Install the eDP metal bracket on the eDP cable and tighten the M2.0 x 5.0 screws.
7.
Route the WLAN and WWAN cables through the routing channels.
8.
Install the:
a.
WLAN card
b.
WWAN card
c.
battery
d.
base cover
9.
Follow the procedure in
After working inside your computer
.
Installing display bezel
NOTE:
The display bezel installation procedure is applicable only for non-touch systems.
1.
Place the display bezel on the display assembly.
2.
Press the edges of the display bezel until it clicks onto the display assembly.
NOTE:
Adhesive is used to secure the display bezel to the display panel.
3.
Install the:
a.
display assembly
b.
WLAN card
c.
WWAN card
d.
battery
e.
base cover
4.
Follow the procedure in
After working inside your computer
.
Disassembly and reassembly
29