BenQ W1090 User Manual - Page 63

the projector., Insert the new lamp into the lamp

Get BenQ W1090 PDF manuals and user guides View all BenQ W1090 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

5. Loosen the captive screws that secure the lamp. • Do not turn the power on with the lamp cover removed. • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries. 6. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 7. Insert the new lamp into the lamp compartment and make sure it fits in the projector. • Ensure the connectors are aligned. • If you experience resistance, lift the lamp and start again. 8. Connect the lamp connector and place as drawing. Lamp connector must be installed flush with the connector base as shown in the image below. A gap between the lamp connector and the connector base will cause damage to the projector. The following images illustrate correct and incorrect lamp connector installations. No Gap Correct Maintenance Gap Incorrect 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Maintenance
63
5.
Loosen the captive screws that secure
the lamp.
•
Do not turn the power on with the lamp
cover removed.
•
Do not insert your fingers between the lamp
and the projector. The sharp edges inside the
projector may cause injuries.
6.
Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out of
the projector.
•
Pulling it too quickly may cause the lamp to
break and scatter broken glass in the
projector.
•
Do not place the lamp in locations where
water might splash on it, children can reach
it, or near flammable materials.
•
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
7.
Insert the new lamp into the lamp
compartment and make sure it fits in the
projector.
•
Ensure the connectors are aligned.
•
If you experience resistance, lift the lamp and
start again.
8.
Connect the lamp connector and place
as drawing.
Lamp connector must be installed flush with the
connector base as shown in the image below. A
gap between the lamp connector and the
connector base will cause damage to the
projector. The following images illustrate correct
and incorrect lamp connector installations.
Correct
Incorrect
Gap
No Gap